What are the common faults of microwave and ultraviolet water treatment equipment, production Aquaculture sterilization equipment Leakage in the water pressure drop equipment system, lack of pressure at the inlet of the high-pressure pump, air leakage, water leakage, blockage of the filter element of the precision filter, high-pressure pump fault, etc. may cause the water pressure drop of the equipment. Solution: Overhaul the high-pressure pump and precision filter, and eliminate problems. Aquaculture sterilization equipment programme The increase of equipment water pressure may be due to the error of high-pressure pump outlet scheduling index and the blockage of the pipeline from high-pressure pump to reverse osmosis equipment. Solution: recover the equipment pressure by dispatching the outlet index of the high-pressure pump and cleaning the pipeline between the high-pressure pump and the reverse osmosis equipment. The decrease in water production of the manufacturers of microwave and ultraviolet water treatment equipment may be due to the lower water temperature, lower water pressure, and pollution and blockage of the reverse osmosis membrane. Solution: recover normal production by adjusting the temperature of raw water and cleaning and replacing the reverse osmosis membrane.

Microwave and ultraviolet water treatment equipment can improve heat exchange efficiency, save energy and reduce consumption. production Aquaculture sterilization equipment The deposits on the surface of the cooler rise by 0. mm every time, High efficiency of heat exchanger can generally reduce 20-30%, and power consumption will increase 4-8%. The selection of organic chemical dosing method can maintain the equipment and extend the service life of the equipment. The etching rate of carbon steel by cooling circulating water without microwave ultraviolet water treatment equipment exceeds 0.5mm/a, Aquaculture sterilization equipment programme The corrosion rate of the solved cooling circulating water on carbon steel is less than 0. mm/a, which can reasonably maintain the equipment and extend the service life of the equipment. Reduce the frequency of routine maintenance to ensure normal operation.

When choosing microwave electrodeless ultraviolet sterilization equipment, there are different wave bands to choose from, production Aquaculture sterilization equipment It is recommended to select disinfector with deep ultraviolet wave band. Because the deep ultraviolet wave band has a wider sterilization range and stronger sterilization ability. Aquaculture sterilization equipment programme In addition, when using the disinfector in the deep ultraviolet wave band, we must pay attention to the radiation dose and time. If the irradiation dose is not enough or the time is too short, there is no way to achieve the expected sterilization effect.

1. The welding of equipment shell and framework shall be firm without obvious deformation or burn through defects. 2. The equipment surface shall be evenly sprayed with the same color, and the surface shall be free of flow marks, bubbles, paint leakage and peeling. 3. The appearance of the equipment shall be neat and beautiful without obvious hammer marks and unevenness. The panel instruments, switches, indicator lights and labels shall be installed firmly and correctly. In order to ensure the stability of the equipment, we need to replace the lamp regularly, production Aquaculture sterilization equipment The imported lamp should be replaced after 9000 hours of continuous service or one year to ensure a high disinfection rate. Aquaculture sterilization equipment programme When replacing the lamp tube, first pull out the power socket of the lamp tube, pull out the lamp tube, then carefully insert the cleaned new lamp tube into the sterilizer, install the gasket, check for water leakage, and then plug in the power supply. Be careful not to touch the quartz glass of the new lamp tube with your fingers, otherwise the disinfection effect will be affected due to stains.

UV disinfection is an efficient, non organic chemical way to prevent mildew, production Aquaculture sterilization equipment The maintenance is low-cost and pollution-free. As a purely physical disinfection method, the microwave electrodeless ultraviolet sterilization equipment can not only reasonably remove most of the microbial strains in the water. Moreover, it is not easy to cause all disinfection and combustion products, thus ensuring that the level of microbial strains in tap water points is within the required product quality standards, Aquaculture sterilization equipment programme The microwave electrodeless ultraviolet sterilization equipment has the advantages of simplicity, convenience, broad-spectrum, high efficiency, pollution-free, convenient management and automation technology.

When microwave ultraviolet water treatment equipment is used, the construction of all equipment must be understood according to the relevant drawings or manufacturing technology, even before the equipment is used, production Aquaculture sterilization equipment Basically, the installation shall be carried out according to the relevant works, and the design shall be carried out according to the size of the whole casing or the relevant actual use needs, the soil of reinforced concrete and other embedded parts, Aquaculture sterilization equipment programme It is also necessary to do a good job in relevant design, and their size and location should meet the design requirements. In the actual treatment process of microwave and ultraviolet water treatment equipment, there will be various processes of construction or acceptance. Of course, as long as the installation of some machinery or other pipeline construction is involved, the welding process will be more or less controlled, and they should refer to the relevant design regulations, Or other standards and related technologies can be used cooperatively.