1. The welding of equipment shell and framework shall be firm without obvious deformation or burn through defects. 2. The equipment surface shall be evenly sprayed with the same color, and the surface shall be free of flow marks, bubbles, paint leakage and peeling. 3. The appearance of the equipment shall be neat and beautiful without obvious hammer marks and unevenness. The panel instruments, switches, indicator lights and labels shall be installed firmly and correctly. In order to ensure the stability of the equipment, we need to replace the lamp regularly, production UV photo oxygen microwave deodorization equipment The imported lamp should be replaced after 9000 hours of continuous service or one year to ensure a high disinfection rate. UV photo oxygen microwave deodorization equipment manufactor When replacing the lamp tube, first pull out the power socket of the lamp tube, pull out the lamp tube, then carefully insert the cleaned new lamp tube into the sterilizer, install the gasket, check for water leakage, and then plug in the power supply. Be careful not to touch the quartz glass of the new lamp tube with your fingers, otherwise the disinfection effect will be affected due to stains.

What are the common faults of microwave and ultraviolet water treatment equipment, production UV photo oxygen microwave deodorization equipment Leakage in the water pressure drop equipment system, lack of pressure at the inlet of the high-pressure pump, air leakage, water leakage, blockage of the filter element of the precision filter, high-pressure pump fault, etc. may cause the water pressure drop of the equipment. Solution: Overhaul the high-pressure pump and precision filter, and eliminate problems. UV photo oxygen microwave deodorization equipment manufactor The increase of equipment water pressure may be due to the error of high-pressure pump outlet scheduling index and the blockage of the pipeline from high-pressure pump to reverse osmosis equipment. Solution: recover the equipment pressure by dispatching the outlet index of the high-pressure pump and cleaning the pipeline between the high-pressure pump and the reverse osmosis equipment. The decrease in water production of the manufacturers of microwave and ultraviolet water treatment equipment may be due to the lower water temperature, lower water pressure, and pollution and blockage of the reverse osmosis membrane. Solution: recover normal production by adjusting the temperature of raw water and cleaning and replacing the reverse osmosis membrane.

To solve the problem of light reactivation: open the channel to realize underground water outflow, to avoid or reduce the visibility of treated water before entering the pipeline. At the same time, use a dark container containing a sample of test water, production UV photo oxygen microwave deodorization equipment It shall be sent for inspection in time to avoid factors such as storage conditions or test time affecting the test results. Improve the light transmittance: adjust the front-end treatment process to reduce the SS mass concentration of water in the UV disinfection device, UV photo oxygen microwave deodorization equipment manufactor The ultraviolet disinfection I was adjusted to ozone decolorization, which reduced the chromaticity of the influent water to ensure that SS was controlled below 10 mg/L; The front-end technology has been adjusted to strictly control the consumption of PAM and other chemicals, and a defoaming device has been installed at the water inlet of the external disinfection device to reduce the foam content in the water body and increase the light transmittance of the water body.

The microwave ultraviolet water treatment equipment has many advantages, such as good light conditions, low energy consumption, thorough sterilization, and flexible installation of equipment. Not only that, the beautiful appearance also attracts many manufacturers to buy. UV photo oxygen microwave deodorization equipment manufactor Ultraviolet germicidal lamp should pay attention to the decline of the irradiation intensity of the lamp tube. After using it for a period of time, we still use the fluorescent lamp concept to evaluate the lamp tube, and judge the invisible light intensity by the intensity of the visible light. This method is prone to errors, production UV photo oxygen microwave deodorization equipment So as to affect the sterilization effect.

The microwave electrodeless ultraviolet sterilization equipment can ensure the sterilization effect and water quality of the effluent. It is a durable and effective sterilization technology. There is no reactivation reaction and no rebound of bacteria, ensuring complete disinfection effect and water quality safety. Compared with other sterilization methods, UV has many obvious advantages, production UV photo oxygen microwave deodorization equipment In particular, unlike chemical fungicides, the ultraviolet sterilizer will not bring toxic substances and residual substances into purified water, UV photo oxygen microwave deodorization equipment manufactor The chemical composition, odor and pH value of the fluid will not be changed. This feature is very important in pharmaceutical industry and related industries. The chemical dosage of influent can often change the characteristics of products.

The microwave ultraviolet water treatment equipment uses quartz sand filter material to remove the suspended solids, sediment, impurities, etc. of larger particles in the raw water and the turbidity of precipitation. In addition, it can also remove many organic substances, bacteria, x, etc. in the water with the decrease of turbidity, and create a good condition for disinfection after filtration. production UV photo oxygen microwave deodorization equipment Use the adsorption capacity of activated carbon to effectively adsorb organic matter, free residual chlorine, colloid, particles, microorganisms UV photo oxygen microwave deodorization equipment manufactor For some metal ions and decolorization, the exchange function of ion resin is used to remove calcium and magnesium ions in raw water to avoid the impact of scaling on subsequent equipment. However, the operation is laborious and material consuming. Now, the dosing system is used to directly add scale inhibitor.