Compared with ordinary vacuum cleaners, the industrial central dust collector has a powerful dust collection function and can be cleaned quickly, avoiding secondary pollution caused by dust and noise pollution: 1. The dusty gas enters the ash hopper of each sub room from the air inlet equalizing pipe of the dust remover. The central dust removal of the workshop is customized and guided by the ash hopper guide device. 　　 2. The large particles of dust are separated and directly fall into the ash hopper, while the fine dust enters the middle box evenly and is adsorbed on the outer surface of the filter bag. Clean gas enters the upper box through the filter bag and is discharged into the atmosphere through offline valves and exhaust pipes. 　　 3. Timing or manual cleaning can be adopted: each chamber of the pulse bag filter will be cleaned in turn, and the chamber that has completed the cleaning will be restored to the dedusting state immediately. 　　 4. Open the electric control pulse valve according to the set procedure, stop air blowing, use the compressed air instantaneous blowing to increase the pressure in the filter bag, shake the dust on the filter bag into the ash bucket, and discharge it by the ash discharge mechanism. 　　 5. With the increasing dust on the outer surface of the filter bag, the differential pressure monitoring system will send a signal when the equipment resistance reaches the set value. 　　 6. The dust removal mechanism starts to work, and compressed air is sprayed from the pulse valve, and then shot into the filter bag through the blowing pipe and nozzle. The filter bag expands and vibrates instantaneously, so that the dust on the surface is removed and dropped into the ash hopper, which is discharged by the ash discharge valve. 　　 7. With the progress of filtering conditions, the dust on the filter bag will accumulate more and more. When the equipment resistance reaches the limited resistance value, the ash removal control device will automatically close the offline valve of one chamber according to the differential pressure setting value or the ash removal time setting value.

During the installation of the microwave and ultraviolet water treatment equipment, the commissioning shall be carried out continuously, production Microwave drying of nuts A lot of work needs to be completed before installation. For example, some of their installations must meet the final installation standards and have the final acceptance standards, so that there can be more ways to deal with it, Microwave drying of nuts Price The operation shall be carried out according to the relevant design requirements as far as possible, and all operations can be accepted during the operation process, so as to ensure the actual use.

With the extension of the use time of the clean microwave ultraviolet water treatment equipment, it is a normal phenomenon that the water production decreases. The decrease of water production in winter is due to the decrease of water temperature and permeability, and the change of reverse osmosis membrane density. These two reasons will reduce the water production of microwave and ultraviolet water treatment equipment. Strengthen pretreatment device, production Microwave drying of nuts Increasing the cleaning time, replacing the filter element frequently, backwashing the reverse osmosis membrane in time, and extending the interval are all ways to promote the normal operation of the microwave ultraviolet water treatment equipment. Microwave drying of nuts Price If the water pipe or microwave ultraviolet water treatment equipment is frozen, the valve shall be closed in time, wrapped with towel, and slowly watered with warm water. Do not directly use fire for barbecue, nor use boiling water for heating, so as to prevent the microwave and ultraviolet water treatment equipment and pipes from cracking, or use a hair dryer to dry them. At the same time, gently tap hard objects on the water pipe until the pipe freezes and thaws, and the tap water flows out smoothly. If the fully automatic frequency conversion water supply equipment has been frozen, it can only be wrapped with a hot towel and sprinkled with warm water until the pipe freezes and thaws, so that the water can flow out smoothly.

Maintaining chlorine or bromine levels in public swimming pools, or even in private swimming pools at home, is an important first stage in preventing bacteria that cause recreational diseases. The weekly test will greatly help you with the proper care you need to keep the pool water clean and safe for everyone to enjoy. Taking time to monitor the level of chemicals in the pool will prevent you from needing to monitor your health later. Microwave drying of nuts Price Installing microwave electrodeless ultraviolet sterilization equipment can eliminate pathogens and bacteria, which will reduce the effectiveness of chlorine and will not leave any residue. production Microwave drying of nuts Ultraviolet is safe and is a widely used sterilization method for water, air and medical supplies. Most people who get sick because of recreational water will have diarrhea, cough, eye pain and even skin rashes. When people enter the pool without taking a shower, they are introducing bacteria, such as sweat, feces and any other bacteria they come in contact with.