RCO organic waste gas catalytic combustion purification equipment can effectively purify the environment, pollution, improve labor operating conditions, ensure the health of workers, and the heat emitted can be recycled to reduce production costs. RCO organic waste gas catalytic combustion equipment has perfect system design, complete auxiliary equipment, high purification efficiency and high automation. RCO organic waste gas catalytic combustion equipment RCO organic waste gas catalytic combustion purification device is designed based on two basic principles of adsorption and catalytic combustion, namely adsorption concentration catalytic combustion method. The dedusting equipment adopts the working mode of single bed adsorption purification of organic waste gas and catalytic combustion device regeneration and activation of activated carbon. Firstly, the organic waste gas with low concentration is adsorbed by activated carbon, and the adsorption operation is stopped when it is almost saturated, then the organic matter is desorbed from the activated carbon by hot gas flow to regenerate the activated carbon; The desorbed organic matter has been concentrated (the concentration is dozens of times higher than the original) and sent to the catalytic combustion chamber for catalytic conversion into CO2 and H2O for emission; When the concentration of organic waste gas reaches above 2000ppm, the organic waste gas can maintain spontaneous combustion in the catalytic bed without external heating. Some of the burned tail gas is discharged into the atmosphere, and most of it is sent to the adsorption bed for desorption and regeneration of activated carbon. In this way, the heat energy required for combustion and desorption can be met to save energy. The regenerated activated carbon can be used for the next adsorption.? RCO organic waste gas catalytic combustion equipment uses catalytic combustion method to convert toxic and harmful organic gas into non-toxic gas.? The main structure of RCO organic waste gas catalytic combustion equipment is composed of three major parts: purification device host, induced draft fan and control system. The catalytic combustion purification device includes: dedusting flame arrester, heat exchanger, preheater and catalytic combustion chamber. The organic waste gas enters the preprocessor from the air inlet at the upper part of the equipment, passes through the coarse filter element composed of multi-layer stainless steel wire mesh to remove dust and other particles in the waste gas, and enters the combined adsorption bed from the main channel at the lower part of the device (two rows in parallel with six grids). Each adsorption bed is equipped with a set of pneumatic switch valve, which can change the adsorption bed into adsorption/desorption state. The longitudinal section of the adsorption bed from bottom to top is respectively the inlet manifold, adsorption chamber, air purification chamber and outlet manifold. The adsorption chamber and the air purification chamber are separated by a flower plate, under which a number of adsorption cylinders are hoisted. The waste gas entering the adsorption chamber passes through the adsorption layer through the outer wall of the adsorption cylinder, VOCs molecules are adsorbed by a large number of microporous surfaces of the adsorbent. After being purified, the waste gas enters the purification chamber upward through the flower plate hole, and then enters the gas outlet header through the switching valve and is discharged by the fan. One of the six adsorption chambers must be in the desorption state, and the other five must be in the adsorption state. Generally, the desorption time is 12 minutes, that is, the adsorption bed responsible for the adsorption work can be desorbed and regenerated once every hour. This work process of the device coincides with the name of the invention zhuanli - a kind of compartment offline desorption bag type adsorption equipment. Its process principle is the same as that of the pulse reverse blow compartment offline bag type dust collector, except that the purification process of the device is "physical adsorption", The bag filter purification process is "physical filtration". The desorption working medium of the adsorption bed is hot air, which is provided by the catalytic combustion device. Generally, the temperature of the hot air is ≤ 150 ℃, which is determined by the boiling point of different VOCs and the saturated vapor partial pressure at the desorption temperature.

Ultraviolet is a kind of light wave invisible to the naked eye, which exists outside the ultraviolet end of the spectrum, so it is called ultraviolet. Ultraviolet ray is one of the electromagnetic waves radiated by the sun. It is a special form of material operation, which is a flow of particles that are not connected. Each UV photon with a wavelength of 253.7 nm has an energy of 4.9 eV. When ultraviolet rays irradiate microorganisms, energy transfer and accumulation will occur, and the accumulation results in the inactivation of microorganisms, thus achieving the purpose of disinfection. When bacteria and viruses absorb more than 3600~65000uW/cm2, it has a strong destructive power on DNA and RNA of bacteria and viruses, and can make bacteria and viruses lose their viability and fecundity, thus eliminating bacteria and viruses, production Breeding sterilization and disinfection equipment Achieve disinfection and sterilization effect. On the one hand, ultraviolet light can mutate nucleic acids, hinder their replication, transcriptional blockade and protein synthesis; On the other hand, the production of free radicals can cause photoionization, which will lead to cell death. Breeding sterilization and disinfection equipment manufactor The sterilization principle of the microwave ultraviolet water treatment equipment is to use the irradiation intensity of the ultraviolet lamp, that is, the irradiation intensity emitted by the ultraviolet sterilization lamp, which is inversely proportional to the distance of the irradiated disinfectant. When the irradiation intensity is constant, the longer the residence time of the irradiated disinfectant is, the closer it is to the sterilization lamp tube, the better the sterilization effect will be. On the contrary, the worse the sterilization effect will be. This equipment can be used in direct drinking water equipment to obtain good water purification effect.

During the installation of the microwave and ultraviolet water treatment equipment, the commissioning shall be carried out continuously, production Breeding sterilization and disinfection equipment A lot of work needs to be completed before installation. For example, some of their installations must meet the final installation standards and have the final acceptance standards, so that there can be more ways to deal with it, Breeding sterilization and disinfection equipment manufactor The operation shall be carried out according to the relevant design requirements as far as possible, and all operations can be accepted during the operation process, so as to ensure the actual use.

During the disinfection process, no toxic and harmful by-products will be produced, the composition and performance of the disinfection water will not be changed, and no secondary pollution will be caused to the water body and the surrounding environment; Reduce chlorine input and residual chlorine, production Breeding sterilization and disinfection equipment The chlorine content in the swimming pool water reduces the disinfection by-products, making the swimming pool environment more healthy. Breeding sterilization and disinfection equipment manufactor Small footprint, safe and reliable operation, simple maintenance and low cost. It can be seen that ultraviolet sterilization has the advantages of sterilization, broad-spectrum sterilization, pollution-free, safe and reliable operation, and no toxic by-products. Therefore, it is increasingly used in engineering.

1. If linear installation is required, please use the installation method of low water inlet and high water outlet to slow down the water flow rate and increase the effect of ultraviolet radiation. 2. When working, Breeding sterilization and disinfection equipment manufactor Do not look directly into your eyes with an ultraviolet lamp. When the equipment is open, repeated opening and closing will seriously affect the service life of the lamp. 3. If the water flow is too fast, please install current limiting and pressure limiting devices. 4. If the turbidity of raw water exceeds 5 degrees, a prefilter should be installed to ensure ultraviolet sterilization. 5. Please take out the quartz sleeve every time. production Breeding sterilization and disinfection equipment After using the disinfection lamp for two to three months, check the surface for dirt to determine the next time to clean the surface of the quartz sleeve.

Application industry: Application scope of electric rapping: it is suitable for casting, metal processing, refractory, ceramics, glass, cement, mineral aggregate, plastic, chemical and other industries and other places with dust pollution.