The catalytic combustion equipment for waste gas treatment is mainly used as a supporting part of the catalytic bed electric heating oxidation combustion system in the CO/RCO adsorption+desorption+catalytic combustion system. It is widely applicable to the purification and odor elimination of hazardous waste gas volatilized or leaked from painting, printing, household appliances, footwear, plastics and various chemical workshops, and is suitable for low concentration (1501000) The organic waste gas that is not suitable for direct combustion or catalytic combustion and recovery treatment will be concentrated by activated carbon adsorption, and then the high concentration organic waste gas will be removed through the desorption procedure and sent to the unit for thermal oxidation reaction. The self heating effect of the organic waste gas catalytic reaction can greatly reduce the heat consumption of the electric heater, especially for the treatment sites with large air volume, Satisfactory economic and social benefits can be obtained. Application scope of exhaust gas catalytic combustion equipment: 1. Industrial applications: common pollutants discharged from petrochemical, light industry, plastics, printing, coating and other industries; 2. Waste gas type application: hydrocarbon compounds (aromatics, alkanes, olefins), benzene, ketones, phenols, alcohols, ethers, alkanes and other compounds; Features of catalytic combustion equipment for waste gas treatment: 1. Convenient operation: fully automatic control during operation. 2. Low energy consumption: during normal operation, the equipment operates at low power (or no power) because the exhaust gas has some concentration. 3. Stable performance: pressure relief and self protection, fire resistance and dust removal, over temperature alarm and automatic control. 4. Low resistance: honeycomb ceramic catalyst impregnated with today's advanced precious metal palladium and platinum has a large specific surface area. 5. Small floor area: only 70% of the same products in the same industry. 6. Long service life: the catalyst is usually replaced within 4 years

The microwave ultraviolet water treatment equipment has many advantages, such as good light conditions, low energy consumption, thorough sterilization, and flexible installation of equipment. Not only that, the beautiful appearance also attracts many manufacturers to buy. Microwave drying equipment Price Ultraviolet germicidal lamp should pay attention to the decline of the radiation intensity of the lamp tube. After using it for a period of time, we still use the fluorescent lamp concept to evaluate the lamp tube, and judge the invisible light intensity by the intensity of the visible light. This method is prone to errors, production Microwave drying equipment So as to affect the sterilization effect.

The microwave electrodeless ultraviolet sterilization equipment can ensure the sterilization effect and water quality of the effluent. It is a durable and effective sterilization technology. There is no reactivation reaction and no rebound of bacteria, ensuring complete disinfection effect and water quality safety. Compared with other sterilization methods, UV has many obvious advantages, production Microwave drying equipment In particular, unlike chemical fungicides, the ultraviolet sterilizer will not bring toxic substances and residual substances into purified water, Microwave drying equipment Price The chemical composition, odor and pH value of the fluid will not be changed. This feature is very important in pharmaceutical industry and related industries. The chemical dosage of influent can often change the characteristics of products.

Ultraviolet sterilization equipment is an extremely effective method against microbial pollution in water. However, production Microwave drying equipment In order to effectively disinfect water, microorganisms must be exposed to an appropriate amount of ultraviolet carbon light. Ultraviolet disinfection systems are used in many different applications, Microwave drying equipment Price From the purification of personal household drinking water to the disinfection of industrial wastewater treatment of the whole urban water supply. UV water treatment is considered to be a safer and more economical method for disinfection of industrial water.

Have you ever thought about whether you need a sterilizer on your water tank? If so, which Z is better? An aquarium scientist's differences between ozone and ultraviolet sterilizers. Ozone is a gas composed of three oxygen atoms, while the oxygen we breathe is composed of two oxygen atoms. This chemical structure makes ozone highly active, production Microwave drying equipment That's why it's such a powerful sterilizer. Microwave drying equipment Price It is meaningful that the bulb in the UV germicidal lamp is made of quartz, because quartz will not filter out the UV rays. However, water filters light according to its depth. Therefore, the water flow space between the quartz bulb and the external glass or plastic tube is usually only a few millimeters - a thicker space will reduce the intensity of ultraviolet rays and allow bacteria and other microorganisms to survive.

When microwave ultraviolet water treatment equipment is used, the construction of all equipment must be understood according to the relevant drawings or manufacturing technology, even before the equipment is used, production Microwave drying equipment Basically, the installation shall be carried out according to the relevant works, and the design shall be carried out according to the size of the whole casing or the relevant actual use needs, the soil of reinforced concrete and other embedded parts, Microwave drying equipment Price It is also necessary to do a good job in relevant design, and their size and location should meet the design requirements. In the actual treatment process of microwave and ultraviolet water treatment equipment, there will be various processes of construction or acceptance. Of course, as long as the installation of some machinery or other pipeline construction is involved, the welding process will be more or less controlled, and they should refer to the relevant design regulations, Or other standards and related technologies can be used cooperatively.