The catalytic combustion equipment for waste gas treatment is mainly used as a supporting part of the catalytic bed electric heating oxidation combustion system in the CO/RCO adsorption+desorption+catalytic combustion system. It is widely applicable to the purification and odor elimination of hazardous waste gas volatilized or leaked from painting, printing, household appliances, footwear, plastics and various chemical workshops, and is suitable for low concentration (1501000) The organic waste gas that is not suitable for direct combustion or catalytic combustion and recovery treatment will be concentrated by activated carbon adsorption, and then the high concentration organic waste gas will be removed through the desorption procedure and sent to the unit for thermal oxidation reaction. The self heating effect of the organic waste gas catalytic reaction can greatly reduce the heat consumption of the electric heater, especially for the treatment sites with large air volume, Satisfactory economic and social benefits can be obtained. Application scope of exhaust gas catalytic combustion equipment: 1. Industrial applications: common pollutants discharged from petrochemical, light industry, plastics, printing, coating and other industries; 2. Waste gas type application: hydrocarbon compounds (aromatics, alkanes, olefins), benzene, ketones, phenols, alcohols, ethers, alkanes and other compounds; Features of catalytic combustion equipment for waste gas treatment: 1. Convenient operation: fully automatic control during operation. 2. Low energy consumption: during normal operation, the equipment operates at low power (or no power) because the exhaust gas has some concentration. 3. Stable performance: pressure relief and self protection, fire resistance and dust removal, over temperature alarm and automatic control. 4. Low resistance: honeycomb ceramic catalyst impregnated with today's advanced precious metal palladium and platinum has a large specific surface area. 5. Small floor area: only 70% of the same products in the same industry. 6. Long service life: the catalyst is usually replaced within 4 years

1. If linear installation is required, please use the installation method of low water inlet and high water outlet to slow down the water flow rate and increase the effect of ultraviolet radiation. 2. When working, Microwave drying of nuts programme Do not look directly into your eyes with an ultraviolet lamp. When the equipment is open, repeated opening and closing will seriously affect the service life of the lamp. 3. If the water flow is too fast, please install current limiting and pressure limiting devices. 4. If the turbidity of raw water exceeds 5 degrees, a prefilter should be installed to ensure ultraviolet sterilization. 5. Please take out the quartz sleeve every time. Customized Microwave drying of nuts After using the disinfection lamp for two to three months, check the surface for dirt to determine the next time to clean the surface of the quartz sleeve.

Ultraviolet sterilization equipment is an extremely effective method against microbial pollution in water. However, Customized Microwave drying of nuts In order to effectively disinfect water, microorganisms must be exposed to an appropriate amount of ultraviolet carbon light. Ultraviolet disinfection systems are used in many different applications, Microwave drying of nuts programme From the purification of personal household drinking water to the disinfection of industrial wastewater treatment of the whole urban water supply. UV water treatment is considered to be a safer and more economical method for disinfection of industrial water.

Ultraviolet is a kind of light wave invisible to the naked eye, which exists outside the ultraviolet end of the spectrum, so it is called ultraviolet. Ultraviolet ray is one of the electromagnetic waves radiated by the sun. It is a special form of material operation, which is a flow of particles that are not connected. Each UV photon with a wavelength of 253.7 nm has an energy of 4.9 eV. When ultraviolet rays irradiate microorganisms, energy transfer and accumulation will occur, and the accumulation results in the inactivation of microorganisms, thus achieving the purpose of disinfection. When bacteria and viruses absorb more than 3600~65000uW/cm2, it has a strong destructive power on DNA and RNA of bacteria and viruses, and can make bacteria and viruses lose their viability and fecundity, thus eliminating bacteria and viruses, Customized Microwave drying of nuts Achieve disinfection and sterilization effect. On the one hand, ultraviolet light can mutate nucleic acids, hinder their replication, transcriptional blockade and protein synthesis; On the other hand, the production of free radicals can cause photoionization, which will lead to cell death. Microwave drying of nuts programme The sterilization principle of the microwave ultraviolet water treatment equipment is to use the irradiation intensity of the ultraviolet lamp, that is, the irradiation intensity emitted by the ultraviolet sterilization lamp, which is inversely proportional to the distance of the irradiated disinfectant. When the irradiation intensity is constant, the longer the residence time of the irradiated disinfectant is, the closer it is to the sterilization lamp tube, the better the sterilization effect will be. On the contrary, the worse the sterilization effect will be. This equipment can be used in direct drinking water equipment to obtain good water purification effect.

Application industry: It is applicable to the disinfection and preservation of air, water, objects, fruits and vegetables, grains and other viruses and bacteria, grain storage, feed bait, marine lakes and other bacterial carriers in indoor and outdoor spaces of all walks of life.

It is mainly used for the gas purification of asphalt, rubber, fertilizer, coking, city gas, metallurgy, building materials, carbon ceramics and other industries, while removing impurities such as tar, dust, water mist, etc., to achieve the dual effect of material recovery and gas purification, which also plays a vital role in ensuring the normal and stable operation of equipment in the later section of the process flow. In addition, It is mainly used as pretreatment device for comprehensive organic waste gas treatment.