Microwave electrodeless ultraviolet sterilization equipment has high value in microwave ultraviolet water treatment equipment, Customized Microwave drying of nuts It destroys and changes the structure of DNA of microorganisms through the irradiation of ultraviolet light, so that the bacteria will die immediately or cannot reproduce, so as to achieve the purpose of sterilization. The real bactericidal effect is UVC ultraviolet, Microwave drying of nuts Price Because C-band ultraviolet light is easily absorbed by the DNA of organisms, the ultraviolet light of about 253.7 nm is preferred. It is a pure physical disinfection method, which has the advantages of simplicity, convenience, broad-spectrum, no secondary pollution, convenient management and automation. With the introduction of various new designed ultraviolet lamps, the application range of ultraviolet sterilization is also expanding.

During the disinfection process, no toxic and harmful by-products will be produced, the composition and performance of the disinfection water will not be changed, and no secondary pollution will be caused to the water body and the surrounding environment; Reduce chlorine input and residual chlorine, Customized Microwave drying of nuts The chlorine content in the swimming pool water reduces the disinfection by-products, making the swimming pool environment more healthy. Microwave drying of nuts Price Small footprint, safe and reliable operation, simple maintenance and low cost. It can be seen that ultraviolet sterilization has the advantages of sterilization, broad-spectrum sterilization, pollution-free, safe and reliable operation, and no toxic by-products. Therefore, it is increasingly used in engineering.

With the extension of the use time of the clean microwave ultraviolet water treatment equipment, it is a normal phenomenon that the water production decreases. The decrease of water production in winter is due to the decrease of water temperature and permeability, and the change of reverse osmosis membrane density. These two reasons will reduce the water production of microwave and ultraviolet water treatment equipment. Strengthen pretreatment device, Customized Microwave drying of nuts Increasing the cleaning time, replacing the filter element frequently, backwashing the reverse osmosis membrane in time, and extending the interval are all ways to promote the normal operation of the microwave ultraviolet water treatment equipment. Microwave drying of nuts Price If the water pipe or microwave ultraviolet water treatment equipment is frozen, the valve shall be closed in time, wrapped with towel, and slowly watered with warm water. Do not directly use fire for barbecue, nor use boiling water for heating, so as to prevent the microwave and ultraviolet water treatment equipment and pipes from cracking, or use a hair dryer to dry them. At the same time, gently tap hard objects on the water pipe until the pipe freezes and thaws, and the tap water flows out smoothly. If the fully automatic frequency conversion water supply equipment has been frozen, it can only be wrapped with a hot towel and sprinkled with warm water until the pipe freezes and thaws, so that the water can flow out smoothly.

RCO organic waste gas catalytic combustion purification equipment can effectively purify the environment, pollution, improve labor operating conditions, ensure the health of workers, and the heat emitted can be recycled to reduce production costs. RCO organic waste gas catalytic combustion equipment has perfect system design, complete auxiliary equipment, high purification efficiency and high automation. RCO organic waste gas catalytic combustion equipment RCO organic waste gas catalytic combustion purification device is designed based on two basic principles of adsorption and catalytic combustion, namely adsorption concentration catalytic combustion method. The dedusting equipment adopts the working mode of single bed adsorption purification of organic waste gas and catalytic combustion device regeneration and activation of activated carbon. Firstly, the organic waste gas with low concentration is adsorbed by activated carbon, and the adsorption operation is stopped when it is almost saturated, then the organic matter is desorbed from the activated carbon by hot gas flow to regenerate the activated carbon; The desorbed organic matter has been concentrated (the concentration is dozens of times higher than the original) and sent to the catalytic combustion chamber for catalytic conversion into CO2 and H2O for emission; When the concentration of organic waste gas reaches above 2000ppm, the organic waste gas can maintain spontaneous combustion in the catalytic bed without external heating. Some of the burned tail gas is discharged into the atmosphere, and most of it is sent to the adsorption bed for desorption and regeneration of activated carbon. In this way, the heat energy required for combustion and desorption can be met to save energy. The regenerated activated carbon can be used for the next adsorption.? RCO organic waste gas catalytic combustion equipment uses catalytic combustion method to convert toxic and harmful organic gas into non-toxic gas.? The main structure of RCO organic waste gas catalytic combustion equipment is composed of three major parts: purification device host, induced draft fan and control system. The catalytic combustion purification device includes: dedusting flame arrester, heat exchanger, preheater and catalytic combustion chamber. The organic waste gas enters the preprocessor from the air inlet at the upper part of the equipment, passes through the coarse filter element composed of multi-layer stainless steel wire mesh to remove dust and other particles in the waste gas, and enters the combined adsorption bed from the main channel at the lower part of the device (two rows in parallel with six grids). Each adsorption bed is equipped with a set of pneumatic switch valve, which can change the adsorption bed into adsorption/desorption state. The longitudinal section of the adsorption bed from bottom to top is respectively the inlet manifold, adsorption chamber, air purification chamber and outlet manifold. The adsorption chamber and the air purification chamber are separated by a flower plate, under which a number of adsorption cylinders are hoisted. The waste gas entering the adsorption chamber passes through the adsorption layer through the outer wall of the adsorption cylinder, VOCs are adsorbed by a large number of microporous surfaces of the adsorbent, and the waste gas is purified and then enters the air purification chamber upward through the flower plate holes, Then it enters the main outlet pipe through the switching valve and is discharged by the fan. One of the six adsorption chambers must be in the desorption state, and the other five must be in the adsorption state. Generally, the desorption time is 12 minutes, that is, the adsorption bed responsible for the adsorption work can be desorbed and regenerated once every hour. This work process of the device coincides with the name of the invention zhuanli - a kind of compartment offline desorption bag type adsorption equipment. Its process principle is the same as that of the pulse reverse blow compartment offline bag type dust collector, except that the purification process of the device is "physical adsorption", The bag filter purification process is "physical filtration". The desorption working medium of the adsorption bed is hot air, which is provided by the catalytic combustion device. Generally, the temperature of the hot air is ≤ 150 ℃, which is determined by the boiling point of different VOCs and the saturated vapor partial pressure at the desorption temperature.

The trapezoidal structure made of food grade transparent silica gel and special mold is used to prevent water leakage caused by improper installation. Microwave drying of nuts Price UV irradiation intensity sensor/UV irradiation intensity monitor: The UV irradiation intensity sensor can monitor the output intensity of the UV disinfection system in real time online, and output mixed signals of 0-5V or 4-20mA for use by the monitor. Customized Microwave drying of nuts The ultraviolet radiation intensity monitor receives the signal provided by the sensor, and can set the radiation intensity alarm value and lamp life according to the requirements. Monitor the system in real time to ensure the normal operation of the equipment.