新上海sh419

 Microwave ultraviolet water treatment equipment
Your current location: home page > Hot information

contact us Contact Us

Shandong Dehai Weilang Energy Equipment Co., Ltd

Contact: Mr. Wang

Tel.: 13001718597

Tel.: 0531-88551699

Email: [email protected]

Address: No. 6, Weihua West Road, Shizhong District, Jinan

Dandong customized microwave liquid sterilization manufacturer

2021-08-14
 Dandong customized microwave liquid sterilization manufacturer

The trapezoidal structure made of food grade transparent silica gel and special mold is used to prevent water leakage caused by improper installation. Microwave liquid sterilization manufactor UV irradiation intensity sensor/UV irradiation intensity monitor: The UV irradiation intensity sensor can monitor the output intensity of the UV disinfection system in real time online, and output mixed signals of 0-5V or 4-20mA for use by the monitor. Customized Microwave liquid sterilization The ultraviolet radiation intensity monitor receives the signal provided by the sensor, and can set the radiation intensity alarm value and lamp life according to the requirements. Monitor the system in real time to ensure the normal operation of the equipment.

 Dandong customized microwave liquid sterilization manufacturer

When installing microwave and ultraviolet water treatment equipment, the command must be strengthened to prevent equipment collision. Customized Microwave liquid sterilization And these important devices are assigned special management, storage and storage problems. Microwave liquid sterilization manufactor In the field of construction, prepare sufficient quantity and quality of fire-fighting tools for inspection, and require them to use only in case of fire. The construction personnel entering the site shall be checked and wear qualified protective equipment, such as safety helmet, because personal safety is very important.

 Dandong customized microwave liquid sterilization manufacturer

The microwave ultraviolet water treatment equipment adopts filters with multiple filter layers, whose primary purpose is to remove the sediment, rust, colloidal substances, suspended solids and other substances with particles of more than 20um in the raw water, Customized Microwave liquid sterilization Manual valve control or full-automatic controller can be selected for a series of operations such as back flushing and forward flushing. Ensure the quality of water produced by the equipment, and extend the service life of microwave and ultraviolet water treatment equipment manufacturers. Microwave liquid sterilization manufactor Check whether the power is cut off and the plug is firmly inserted. Check whether the wiring plug of the low-voltage switch of the microwave ultraviolet water treatment equipment falls or fails to work so that the power contact cannot return. Check whether the connecting wire of each terminal falls off, and check whether the water pressure of tap water is too low, so that the low-voltage switch does not work.

 Dandong customized microwave liquid sterilization manufacturer

UV disinfection is generally only used for air and instrument surface disinfection. Surgical dressings cannot be treated by UV radiation as a routine method. Ultraviolet radiation is the general term of radiation in electromagnetic spectrum with wavelength from 10nm to 400nm, which can not cause people's vision. In 1801, German physicist Ritter found that the ultraviolet ray could sensitize the photographic negative containing silver bromide at the outer part of the ultraviolet end of the sunlight spectrum, so he found the existence of ultraviolet ray. Too much ultraviolet rays entering the body will cause skin cancer. Customized Microwave liquid sterilization It can be disinfected after use every day. It should be disinfected two or three times a week. It is recommended that the toothbrush head should be replaced every three months. It can be disinfected every day. The SEGA toothbrush sterilizer I selected should be disinfected for 6-8 minutes each time. It is a good ultraviolet disinfection lamp. It needs to be equipped with a ballast. Mould formation is due to long-term lack of ventilation and humidity, Microwave liquid sterilization manufactor If ventilation and moisture removal are available, mold will not grow. Since mold has been formed, first kill it with a mold remover, and then put a moisture bag such as a charcoal bag. I often do on-site mildew and odor removal projects. You can sprinkle lime on the corner of the wall or place charcoal in the house to absorb moisture when the house is wet. In addition, don't open the window in foggy or rainy weather. Open the window in good weather to ventilate in time.

 Dandong customized microwave liquid sterilization manufacturer

According to different lamp tubes, ultraviolet sterilization lamps have thermal cathode low-pressure mercury vapor discharge lamps and cathode low-pressure mercury vapor discharge lamps; The hot cathode low-pressure mercury vapor discharge lamps can be divided into straight type, H-type, U-type tube, etc. from the appearance; Customized Microwave liquid sterilization For different needs, it can be divided into low (no ozone), ozone, high ozone, etc. The portable microwave electrodeless ultraviolet sterilization equipment can be used for close mobile irradiation, and the ultraviolet lamp suspension irradiation can also be used. Small articles can be irradiated in the ultraviolet disinfection box. Different kinds of microorganisms have different sensitivity to ultraviolet rays. When using ultraviolet rays for disinfection, the radiation dose must be used to reach the radiation dose required to kill the target microorganisms. Microwave liquid sterilization manufactor The product of the irradiation intensity and irradiation time of the ultraviolet lamp used for irradiation dose at the surface of the irradiated object. Therefore, according to the irradiation intensity of the ultraviolet light source, the required irradiation time can be calculated.

Share to