新上海sh419

 Microwave ultraviolet water treatment equipment
Your current location: home page > Hot information

contact us Contact Us

Shandong Dehai Weilang Energy Equipment Co., Ltd

Contact: Mr. Wang

Tel.: 13001718597

Tel.: 0531-88551699

Email: [email protected]

Address: No. 6, Weihua West Road, Shizhong District, Jinan

Shanghai Customized Microwave Wood Drying Equipment Manufacturer

2021-08-20
 Shanghai Customized Microwave Wood Drying Equipment Manufacturer

Ultraviolet disinfection belongs to physical instant disinfection technology, which can keep sterile under the condition that the water body is not polluted. When the treated water leaves the disinfection reactor, Customized Microwave wood drying equipment Some microorganisms killed by ultraviolet light will repair damaged molecules and regenerate bacteria under visible light irradiation, which is called light reactivation. Microwave wood drying equipment manufactor Some bacteria can also repair themselves under the condition of no light, that is, dark reactivation. According to the current research results, photoreactivation is the main way of most microbial remediation and also the main control target.

 Shanghai Customized Microwave Wood Drying Equipment Manufacturer

In the microwave and ultraviolet water treatment equipment, the reverse osmosis equipment needs three kinds of sealing rings to realize the sealing barrier of each part of the membrane shell. In order to reduce the resistance of the device, water or glycerin should be added to the surface of the sealing ring. Customized Microwave wood drying equipment Microwave ultraviolet water treatment equipment PP cotton softening equipment. Microwave wood drying equipment manufactor Special attention should be paid to the use of petroleum jelly or other petroleum grease lubricants as lubricants. Otherwise, the fresh water pipeline will crack, especially the expansion of the sealant ring. The expansion of the skirt does not directly affect the operation of the system, but will affect the reloading of the system after unloading, that is, the expansion skirt is difficult to enter the slot during loading.

 Shanghai Customized Microwave Wood Drying Equipment Manufacturer

1. If linear installation is required, please use the installation method of low water inlet and high water outlet to slow down the water flow rate and increase the effect of ultraviolet radiation. 2. When working, Microwave wood drying equipment manufactor Do not look directly into your eyes with an ultraviolet lamp. When the equipment is open, repeated opening and closing will seriously affect the service life of the lamp. 3. If the water flow is too fast, please install current limiting and pressure limiting devices. 4. If the turbidity of raw water exceeds 5 degrees, a prefilter should be installed to ensure ultraviolet sterilization. 5. Please take out the quartz sleeve every time. Customized Microwave wood drying equipment After using the disinfection lamp for two to three months, check the surface for dirt to determine the next time to clean the surface of the quartz sleeve.

 Shanghai Customized Microwave Wood Drying Equipment Manufacturer

1. The welding of equipment shell and framework shall be firm without obvious deformation or burn through defects. 2. The equipment surface shall be evenly sprayed with the same color, and the surface shall be free of flow marks, bubbles, paint leakage and peeling. 3. The appearance of the equipment shall be neat and beautiful without obvious hammer marks and unevenness. The panel instruments, switches, indicator lights and labels shall be installed firmly and correctly. In order to ensure the stability of the equipment, we need to replace the lamp regularly, Customized Microwave wood drying equipment The imported lamp should be replaced after 9000 hours of continuous service or one year to ensure a high disinfection rate. Microwave wood drying equipment manufactor When replacing the lamp tube, first pull out the power socket of the lamp tube, pull out the lamp tube, then carefully insert the cleaned new lamp tube into the sterilizer, install the gasket, check for water leakage, and then plug in the power supply. Be careful not to touch the quartz glass of the new lamp tube with your fingers, otherwise the disinfection effect will be affected due to stains.

 Shanghai Customized Microwave Wood Drying Equipment Manufacturer

Swimming and playing other water sports are exciting ways, Customized Microwave wood drying equipment You can relax and exercise at the same time! Some sunshine, physical exercise and laughter all advocate a healthy life. You can spend endless time in the water with your friends and family, but it is responsible to enjoy the fun in the carefree sunshine. A healthy swimming pool is not only visually clean, but also has proper chemical balance, Microwave wood drying equipment manufactor These chemical balances should not overwhelm your senses. If you like swimming pools, you will hear about bacteria such as Giardia, Cryptosporidium and Legionella. Installing an ultraviolet sterilizer will eliminate the bacteria and parasites that cause these diseases, and keep your swimming pool water clear and transparent with confidence!

 Shanghai Customized Microwave Wood Drying Equipment Manufacturer

UV disinfection is generally only used for air and instrument surface disinfection. Surgical dressings cannot be treated by UV radiation as a routine method. Ultraviolet radiation is the general term of radiation in electromagnetic spectrum with wavelength from 10nm to 400nm, which can not cause people's vision. In 1801, German physicist Ritter found that the ultraviolet ray could sensitize the photographic negative containing silver bromide at the outer part of the ultraviolet end of the sunlight spectrum, so he found the existence of ultraviolet ray. Too much ultraviolet rays entering the body will cause skin cancer. Customized Microwave wood drying equipment It can be disinfected after use every day. It should be disinfected two or three times a week. It is recommended that the toothbrush head should be replaced every three months. It can be disinfected every day. The SEGA toothbrush sterilizer I selected should be disinfected for 6-8 minutes each time. It is a good ultraviolet disinfection lamp. It needs to be equipped with a ballast. Mould formation is due to long-term lack of ventilation and humidity, Microwave wood drying equipment manufactor If ventilation and moisture removal are available, mold will not grow. Since mold has been formed, first kill it with a mold remover, and then put a moisture bag such as a charcoal bag. I often do on-site mildew and odor removal projects. You can sprinkle lime on the corner of the wall or place charcoal in the house to absorb moisture when the house is wet. In addition, don't open the window in foggy or rainy weather. Open the window in good weather to ventilate in time.

Share to