Microwave electrodeless ultraviolet sterilization equipment is a widely used and effective water disinfection equipment, which can use ultraviolet light to eliminate bacteria, viruses and other microorganisms in water under safe and harmless conditions. Customized Microwave heating equipment The specific application of the ultraviolet sterilizer is as follows: the working principle of the microwave electrodeless ultraviolet sterilization equipment is to use the ultraviolet lamp to generate ultraviolet light to irradiate the water body, thus playing the role of killing bacteria and viruses in the water body. The disinfection process is stable and non-toxic, and will not produce harmful substances to the water body. Microwave heating equipment manufactor UV sterilizer is often used for disinfection of water supply in residential areas, schools, factories and food factories. It is an effective equipment for disinfection of secondary water supply of drinking water and domestic water. In addition, the ultraviolet sterilizer can also be used for water disinfection of swimming pools.

With the extension of the use time of the clean microwave ultraviolet water treatment equipment, it is a normal phenomenon that the water production decreases. The decrease of water production in winter is due to the decrease of water temperature and permeability, and the change of reverse osmosis membrane density. These two reasons will reduce the water production of microwave and ultraviolet water treatment equipment. Strengthen pretreatment device, Customized Microwave heating equipment Increasing the cleaning time, replacing the filter element frequently, backwashing the reverse osmosis membrane in time, and extending the interval are all ways to promote the normal operation of the microwave ultraviolet water treatment equipment. Microwave heating equipment manufactor If the water pipe or microwave ultraviolet water treatment equipment is frozen, the valve shall be closed in time, wrapped with towel, and slowly watered with warm water. Do not directly use fire for barbecue, nor use boiling water for heating, so as to prevent the microwave and ultraviolet water treatment equipment and pipes from cracking, or use a hair dryer to dry them. At the same time, gently tap hard objects on the water pipe until the pipe freezes and thaws, and the tap water flows out smoothly. If the fully automatic frequency conversion water supply equipment has been frozen, it can only be wrapped with a hot towel and sprinkled with warm water until the pipe freezes and thaws, so that the water can flow out smoothly.

VOCS catalytic combustion waste gas treatment equipment in paint shop: Catalytic combustion equipment is a kind of deodorization and deodorization waste gas treatment equipment. The concept of catalytic combustion is to use the catalytic incineration reaction of combustibles under the effect of catalyst and certain temperature conditions. Combustibles are burned under the effect of catalyst. Compared with direct incineration, catalytic incineration has a lower temperature and is quite safe. Catalytic principle and equipment composition (1) Catalyst is defined as a substance that can improve the rate of chemical reaction, control the direction of reaction, and keep its chemical properties unchanged before and after reaction. (2) The mechanism of catalytic effect The mechanism of catalytic effect is a very complicated problem, which is only briefly introduced here. In a chemical reaction process, the participation of the catalyst cannot change the original chemical balance, but only the speed of the chemical reaction. Before and after the reaction, the nature of the catalyst itself does not change. So, how does the catalyst speed up the response? The catalyst has not changed before and after the reaction, so has the catalyst participated in the reaction? In practice, the catalyst itself has participated in the reaction. It is because of its participation that the reaction has changed the original path, reduced the activation energy, and then accelerated the reaction speed. For example, the reaction A+B → C is transited through the central active complex (AB), that is, the reaction speed of A+B → [AB] → C is slow. After participating in catalyst K, the reaction is completed in an easy way: A+B+2K → [AK]+[BK] → [CK]+K → C+2K center no longer needs the transition from [AB] to C, and then the reaction speed is accelerated without changing the catalyst properties. (3) Process composition of catalytic incineration equipment: different emission occasions and different exhaust gases have different process flows. However, no matter which process flow is adopted, it is composed of the following process units. ① Waste gas pretreatment In order to avoid blocking of the catalyst bed and catalyst poisoning, it is necessary to pretreat the waste gas before entering the bed to remove the dust, droplets and catalyst poisons in the waste gas. ② Preheating equipment Preheating equipment includes waste gas preheating equipment and catalyst incinerator preheating equipment. Because all catalysts have a catalytic activity temperature, it is called catalyst ignition temperature for catalytic incineration. It is necessary to make the temperature of exhaust gas and bed reach the ignition temperature before catalytic incineration. Therefore, it is necessary to set up preheating equipment. However, for occasions where the exhaust gas temperature is high, such as enameled wire, insulating material, baking varnish, etc., and the temperature can reach more than 300 ℃, preheating equipment is not required. The hot gas heated by the preheating equipment can be arranged in the heat exchanger and bed. The heat source of the preheater can be flue gas or electric heating, and now electric heating is more used. When catalytic reaction starts, exhaust gas can be preheated with recovered reaction heat as far as possible. In the case of high reaction heat, waste heat recovery equipment should also be set to save power. The heat source temperature of preheated exhaust gas generally exceeds the catalyst activity temperature. In order to maintain the catalyst, the heating equipment should be kept a certain distance from the catalytic incineration equipment, so that the exhaust gas temperature can be evenly distributed. Starting from the need for preheating, catalytic incineration is applicable to the purification of continuous exhaust. If intermittent exhaust, not only each preheating needs energy, but also the reaction heat can not be recycled, which will result in great power waste. This should be noted in planning and selection. ③ Fixed bed catalytic reverberator is generally selected as catalytic incineration equipment. The planning of the reverberator shall be carried out according to the standard, which shall be convenient for operation, repair and catalyst loading and unloading. In the process planning of catalytic incineration, it is necessary to plan the built-up process of components according to the specific situation in the case of large air volume, that is, the preheater and the reverberator are installed separately, and the pipes are connected between them. For occasions with small air volume, catalytic incinerators can be selected to combine preheating and reaction, but pay attention to the distance between preheating section and reaction section. In the catalytic incineration of organic waste gas, the organic waste gas to be treated is easy to explode when mixed with air at high temperature, so the safety problem is very important. Therefore, on the one hand, it is necessary to control the mixing ratio of organic matter and air to keep it at the lower explosive limit; On the other hand, the catalytic incineration system should be equipped with monitoring and alarm equipment and explosion-proof measures.

To solve the problem of light reactivation: open the channel to realize underground water outflow, to avoid or reduce the visibility of treated water before entering the pipeline. At the same time, use a dark container containing a sample of test water, Customized Microwave heating equipment It shall be sent for inspection in time to avoid factors such as storage conditions or test time affecting the test results. Improve the light transmittance: adjust the front-end treatment process to reduce the SS mass concentration of water in the UV disinfection device, Microwave heating equipment manufactor The ultraviolet disinfection I was adjusted to ozone decolorization, which reduced the chromaticity of the influent water to ensure that SS was controlled below 10 mg/L; The front-end technology has been adjusted to strictly control the consumption of PAM and other chemicals, and a defoaming device has been installed at the water inlet of the external disinfection device to reduce the foam content in the water body and increase the light transmittance of the water body.

Now people pay more attention to health, and the demand for ultraviolet disinfection equipment will be more and more extensive. Customized Microwave heating equipment The UV sterilization equipment is highly integrated, with low maintenance costs, which saves the time and energy of operators without adding any other chemical reagents. UVC ultraviolet ray plays a real role in disinfection equipment, Microwave heating equipment manufactor The ultraviolet radiation can destroy and change the DNA (deoxyribonucleic acid) structure of microorganisms, so that the bacteria will die immediately or cannot reproduce, so as to achieve the purpose of sterilization.

Have you ever thought about whether you need a sterilizer on your water tank? If so, which Z is better? An aquarium scientist's differences between ozone and ultraviolet sterilizers. Ozone is a gas composed of three oxygen atoms, while the oxygen we breathe is composed of two oxygen atoms. This chemical structure makes ozone highly active, Customized Microwave heating equipment That's why it's such a powerful sterilizer. Microwave heating equipment manufactor It is meaningful that the bulb in the UV germicidal lamp is made of quartz, because quartz will not filter out the UV rays. However, water filters light according to its depth. Therefore, the water flow space between the quartz bulb and the external glass or plastic tube is usually only a few millimeters - a thicker space will reduce the intensity of ultraviolet rays and allow bacteria and other microorganisms to survive.