The technology of microwave ultraviolet water treatment equipment is to use double layer ultrafiltration membrane for microwave ultraviolet water treatment equipment, or combine ultrafiltration membrane and reverse osmosis filtration membrane for application. UV photo oxygen microwave deodorization equipment programme When the manufacturer of microwave ultraviolet water treatment equipment applies external pressure on the concentrated solution side, the penetration speed will decrease. When the pressure increases to a certain value, the penetration process will stop and the so-called penetration balance will be reached. The external pressure under the balance condition is called the penetration pressure. When the pressure on the concentrated solution side continues to increase, that is, when the applied pressure is greater than the penetration pressure, The solvent of purified water equipment will reverse its original soaking direction and enter the dilute solution side from the concentrated solution side through the semi permeable membrane, production UV photo oxygen microwave deodorization equipment This phenomenon is called reverse osmosis. For a long time, it will not only affect the effluent quality of the equipment, but also lead to the fouling of the reverse osmosis membrane of the main components of the equipment, resulting in the small output of the pure water equipment, the substandard effluent quality, or the equipment can not be used. In order to ensure the continuous and safe operation of pure water equipment, the maintenance of pure water equipment is very important.

During the disinfection process, no toxic and harmful by-products will be produced, the composition and performance of the disinfection water will not be changed, and no secondary pollution will be caused to the water body and the surrounding environment; Reduce chlorine input and residual chlorine, production UV photo oxygen microwave deodorization equipment The chlorine content in the swimming pool water reduces the disinfection by-products, making the swimming pool environment more healthy. UV photo oxygen microwave deodorization equipment programme Small footprint, safe and reliable operation, simple maintenance and low cost. It can be seen that ultraviolet sterilization has the advantages of sterilization, broad-spectrum sterilization, pollution-free, safe and reliable operation, and no toxic by-products. Therefore, it is increasingly used in engineering.

RCO organic waste gas catalytic combustion purification equipment can effectively purify the environment, pollution, improve labor operating conditions, ensure the health of workers, and the heat emitted can be recycled to reduce production costs. RCO organic waste gas catalytic combustion equipment has perfect system design, complete auxiliary equipment, high purification efficiency and high automation. RCO organic waste gas catalytic combustion equipment RCO organic waste gas catalytic combustion purification device is designed based on two basic principles of adsorption and catalytic combustion, namely adsorption concentration catalytic combustion method. The dedusting equipment adopts the working mode of single bed adsorption purification of organic waste gas and catalytic combustion device regeneration and activation of activated carbon. Firstly, the organic waste gas with low concentration is adsorbed by activated carbon, and the adsorption operation is stopped when it is almost saturated, then the organic matter is desorbed from the activated carbon by hot gas flow to regenerate the activated carbon; The desorbed organic matter has been concentrated (the concentration is dozens of times higher than the original) and sent to the catalytic combustion chamber for catalytic conversion into CO2 and H2O for emission; When the concentration of organic waste gas reaches above 2000ppm, the organic waste gas can maintain spontaneous combustion in the catalytic bed without external heating. Some of the burned tail gas is discharged into the atmosphere, and most of it is sent to the adsorption bed for desorption and regeneration of activated carbon. In this way, the heat energy required for combustion and desorption can be met to save energy. The regenerated activated carbon can be used for the next adsorption.? RCO organic waste gas catalytic combustion equipment uses catalytic combustion method to convert toxic and harmful organic gas into non-toxic gas.? The main structure of RCO organic waste gas catalytic combustion equipment is composed of three major parts: purification device host, induced draft fan and control system. The catalytic combustion purification device includes: dedusting flame arrester, heat exchanger, preheater and catalytic combustion chamber. The organic waste gas enters the preprocessor from the air inlet at the upper part of the equipment, passes through the coarse filter element composed of multi-layer stainless steel wire mesh to remove dust and other particles in the waste gas, and enters the combined adsorption bed from the main channel at the lower part of the device (two rows in parallel with six grids). Each adsorption bed is equipped with a set of pneumatic switch valve, which can change the adsorption bed into adsorption/desorption state. The longitudinal section of the adsorption bed from bottom to top is respectively the inlet manifold, adsorption chamber, air purification chamber and outlet manifold. The adsorption chamber and the air purification chamber are separated by a flower plate, under which a number of adsorption cylinders are hoisted. The waste gas entering the adsorption chamber passes through the adsorption layer through the outer wall of the adsorption cylinder, VOCs molecules are adsorbed by a large number of microporous surfaces of the adsorbent. After being purified, the waste gas enters the purification chamber upward through the flower plate hole, and then enters the gas outlet header through the switching valve and is discharged by the fan. One of the six adsorption chambers must be in the desorption state, and the other five must be in the adsorption state. Generally, the desorption time is 12 minutes, that is, the adsorption bed responsible for the adsorption work can be desorbed and regenerated once every hour. This work process of the device coincides with the name of the invention zhuanli - a kind of compartment offline desorption bag type adsorption equipment. Its process principle is the same as that of the pulse reverse blow compartment offline bag type dust collector, except that the purification process of the device is "physical adsorption", The bag filter purification process is "physical filtration". The desorption working medium of the adsorption bed is hot air, which is provided by the catalytic combustion device. Generally, the temperature of the hot air is ≤ 150 ℃, which is determined by the boiling point of different VOCs and the saturated vapor partial pressure at the desorption temperature.

Application industry: It is used for liquid purification such as water and paint, solid-liquid separation in machinery, metallurgy, chemical industry, prevention and control, printing, electric lock, medicine, food and other industries, food and beverage, fruit wine, biochemical water treatment, high-end aquaculture, etc.

Compared with ordinary vacuum cleaners, the industrial central dust collector has a powerful dust collection function and can be cleaned quickly, avoiding secondary pollution caused by dust and noise pollution: 1. The dusty gas enters the ash hopper of each sub room from the air inlet equalizing pipe of the dust remover. The central dust removal of the workshop is customized and guided by the ash hopper guide device. 　　 2. The large particles of dust are separated and directly fall into the ash hopper, while the fine dust enters the middle box evenly and is adsorbed on the outer surface of the filter bag. Clean gas enters the upper box through the filter bag and is discharged into the atmosphere through offline valves and exhaust pipes. 　　 3. Timing or manual cleaning can be adopted: each chamber of the pulse bag filter will be cleaned in turn, and the chamber that has completed the cleaning will be restored to the dedusting state immediately. 　　 4. Open the electric control pulse valve according to the set procedure, stop air blowing, use the compressed air instantaneous blowing to increase the pressure in the filter bag, shake the dust on the filter bag into the ash bucket, and discharge it by the ash discharge mechanism. 　　 5. With the increasing dust on the outer surface of the filter bag, the differential pressure monitoring system will send a signal when the equipment resistance reaches the set value. 　　 6. The dust removal mechanism starts to work, and compressed air is sprayed from the pulse valve, and then shot into the filter bag through the blowing pipe and nozzle. The filter bag expands and vibrates instantaneously, so that the dust on the surface is removed and dropped into the ash hopper, which is discharged by the ash discharge valve. 　　 7. With the progress of filtering conditions, the dust on the filter bag will accumulate more and more. When the equipment resistance reaches the limited resistance value, the ash removal control device will automatically close the offline valve of one chamber according to the differential pressure setting value or the ash removal time setting value.

The microwave electrodeless ultraviolet sterilization equipment can ensure the sterilization effect and water quality of the effluent. It is a durable and effective sterilization technology. There is no reactivation reaction and no rebound of bacteria, ensuring complete disinfection effect and water quality safety. Compared with other sterilization methods, UV has many obvious advantages, production UV photo oxygen microwave deodorization equipment In particular, unlike chemical fungicides, the ultraviolet sterilizer will not bring toxic substances and residual substances into purified water, UV photo oxygen microwave deodorization equipment programme The chemical composition, odor and pH value of the fluid will not be changed. This feature is very important in pharmaceutical industry and related industries. The chemical dosage of influent can often change the characteristics of products.