The microwave ultraviolet water treatment equipment adopts filters with multiple filter layers, whose primary purpose is to remove the sediment, rust, colloidal substances, suspended solids and other substances with particles of more than 20um in the raw water, Customized Microwave liquid sterilization Manual valve control or full-automatic controller can be selected for a series of operations such as back flushing and forward flushing. Ensure the quality of water produced by the equipment, and extend the service life of microwave and ultraviolet water treatment equipment manufacturers. Microwave liquid sterilization Price Check whether the power is cut off and the plug is firmly inserted. Check whether the wiring plug of the low-voltage switch of the microwave ultraviolet water treatment equipment falls or fails to work so that the power contact cannot return. Check whether the connecting wire of each terminal falls off, and check whether the water pressure of tap water is too low, so that the low-voltage switch does not work.

To solve the problem of light reactivation: open the channel to realize underground water outflow, to avoid or reduce the visibility of treated water before entering the pipeline. At the same time, use a dark container containing a sample of test water, Customized Microwave liquid sterilization It shall be sent for inspection in time to avoid factors such as storage conditions or test time affecting the test results. Improve the light transmittance: adjust the front-end treatment process to reduce the SS mass concentration of water in the UV disinfection device, Microwave liquid sterilization Price The ultraviolet disinfection I was adjusted to ozone decolorization, which reduced the chromaticity of the influent water to ensure that SS was controlled below 10 mg/L; The front-end technology has been adjusted to strictly control the consumption of PAM and other chemicals, and a defoaming device has been installed at the water inlet of the external disinfection device to reduce the foam content in the water body and increase the light transmittance of the water body.

1. If linear installation is required, please use the installation method of low water inlet and high water outlet to slow down the water flow rate and increase the effect of ultraviolet radiation. 2. When working, Microwave liquid sterilization Price Do not look directly into your eyes with an ultraviolet lamp. When the equipment is open, repeated opening and closing will seriously affect the service life of the lamp. 3. If the water flow is too fast, please install current limiting and pressure limiting devices. 4. If the turbidity of raw water exceeds 5 degrees, a prefilter should be installed to ensure ultraviolet sterilization. 5. Please take out the quartz sleeve every time. Customized Microwave liquid sterilization After using the disinfection lamp for two to three months, check the surface for dirt to determine the next time to clean the surface of the quartz sleeve.

UV disinfection is generally only used for air and instrument surface disinfection. Surgical dressings cannot be treated by UV radiation as a routine method. Ultraviolet radiation is the general term of radiation in electromagnetic spectrum with wavelength from 10nm to 400nm, which can not cause people's vision. In 1801, German physicist Ritter found that the ultraviolet ray could sensitize the photographic negative containing silver bromide at the outer part of the ultraviolet end of the sunlight spectrum, so he found the existence of ultraviolet ray. Too much ultraviolet rays entering the body will cause skin cancer. Customized Microwave liquid sterilization It can be disinfected after use every day. It should be disinfected two or three times a week. It is recommended that the toothbrush head should be replaced every three months. It can be disinfected every day. The SEGA toothbrush sterilizer I selected should be disinfected for 6-8 minutes each time. It is a good ultraviolet disinfection lamp. It needs to be equipped with a ballast. Mould formation is due to long-term lack of ventilation and humidity, Microwave liquid sterilization Price If ventilation and moisture removal are available, mold will not grow. Since mold has been formed, first kill it with a mold remover, and then put a moisture bag such as a charcoal bag. I often do on-site mildew and odor removal projects. You can sprinkle lime on the corner of the wall or place charcoal in the house to absorb moisture when the house is wet. In addition, don't open the window in foggy or rainy weather. Open the window in good weather to ventilate in time.

Ultraviolet disinfection belongs to physical instant disinfection technology, which can keep sterile under the condition that the water body is not polluted. When the treated water leaves the disinfection reactor, Customized Microwave liquid sterilization Some microorganisms killed by ultraviolet light will repair damaged molecules and regenerate bacteria under visible light irradiation, which is called light reactivation. Microwave liquid sterilization Price Some bacteria can also repair themselves under the condition of no light, that is, dark reactivation. According to the current research results, photoreactivation is the main way of most microbial remediation and also the main control target.

Intelligent sprinkler system Intelligent high-pressure fog pile system Fusen deodorization of waste transfer station