The microwave ultraviolet water treatment equipment uses quartz sand filter material to remove the suspended solids, sediment, impurities, etc. of larger particles in the raw water and the turbidity of precipitation. In addition, it can also remove many organic substances, bacteria, x, etc. in the water with the decrease of turbidity, and create a good condition for disinfection after filtration. production Pet feed deodorization equipment Use the adsorption capacity of activated carbon to effectively adsorb organic matter, free residual chlorine, colloid, particles, microorganisms Pet feed deodorization equipment manufactor For some metal ions and decolorization, the exchange function of ion resin is used to remove calcium and magnesium ions in raw water to avoid the impact of scaling on subsequent equipment. However, the operation is laborious and material consuming. Now, the dosing system is used to directly add scale inhibitor.

Maintaining chlorine or bromine levels in public swimming pools, or even in private swimming pools at home, is an important first stage in preventing bacteria that cause recreational diseases. The weekly test will greatly help you with the proper care you need to keep the pool water clean and safe for everyone to enjoy. Taking time to monitor the level of chemicals in the pool will prevent you from needing to monitor your health later. Pet feed deodorization equipment manufactor Installing microwave electrodeless ultraviolet sterilization equipment can eliminate pathogens and bacteria, which will reduce the effectiveness of chlorine and will not leave any residue. production Pet feed deodorization equipment Ultraviolet is safe and is a widely used sterilization method for water, air and medical supplies. Most people who get sick because of recreational water will have diarrhea, cough, eye pain and even skin rashes. When people enter the pool without taking a shower, they are introducing bacteria, such as sweat, feces and any other bacteria they come in contact with.

Application industry: Application scope of electric rapping: it is suitable for casting, metal processing, refractory, ceramics, glass, cement, mineral aggregate, plastic, chemical and other industries and other places with dust pollution.

Activated carbon adsorption and catalytic combustion equipment is a common volatile organic waste gas treatment equipment. It is energy-saving, environmental protection, no secondary pollution, and high purification efficiency. It is a very good equipment for VOC waste gas treatment. Generally, the main components of activated carbon adsorption catalytic combustion equipment are as follows: Pretreatment equipment: since honeycomb activated carbon adsorption requires specific conditions such as temperature, humidity and cleanliness, it is necessary to treat the organic waste gas with different characteristics before entering the activated carbon adsorption. The organic waste gas containing more dust particles needs to be filtered. The waste gas with a temperature greater than 45 ℃ needs to be cooled, and the waste gas containing a large number of water mist particles needs to be separated and filtered. Activated carbon adsorption bed: it can absorb organic waste gas by taking advantage of the porous physical characteristics of activated carbon. The design of the adsorption bed follows the law of two-phase adsorption curve. Only by combining the amount of activated carbon and calculating the cross section wind speed and retention time of activated carbon adsorption can the adsorption efficiency meet the design requirements and meet the emission standards. The box is in negative pressure state during equipment operation, and it is required to be air tight. The desorption temperature of the box is between 70-100 ℃ during the desorption process, and the heat preservation is generally 50mm considering the energy saving and safety factors. Ensure that the temperature of the outer wall of the box is not higher than the normal temperature by 15 ℃. Main exhaust fan: as the main power of the equipment, the exhaust fan guides the air to move according to the specified process. The fan can be selected accurately only when it is stable and reliable, and the resistance calculation of the system is accurate. The operation of the fan will produce noise, and the high-power fan needs to be equipped with a sound insulation room. Attention shall be paid to the design that the wind speed at the air outlet shall not be too high. Catalytic combustion equipment: after the system has operated for a period of time, the activated carbon needs to be regenerated after adsorption saturation to restore the adsorption activity of the activated carbon. The organic waste gas is concentrated in the activated carbon. After the organic matter is separated from the activated carbon layer at low temperature, it is decomposed into water and carbon dioxide at about 300 ℃ through the action of catalyst. At the same time, the energy is released. The energy is replaced by the heat exchange device to maintain the energy of spontaneous combustion of the equipment. For a single activated carbon adsorption bed, the desorption time is 2-2.5 hours. The set time of activated carbon adsorption box is automatically switched to desorption regularly. The service life of the ceramic honeycomb noble metal catalyst loaded inside is 8000 hours. The whole desorption system adopts multi-point temperature control to ensure the stability of desorption effect. The selection of organic waste gas catalyst is the core of this equipment. Valve switching system: valves include adsorption system valve, desorption system valve, cooling and emergency discharge valve. The three types of valves are required to be timely and accordingly to ensure that the air leakage rate is less than 2%. The conventional galvanized sheet air valve in the market has air leakage due to unreliable sealing, so it is necessary to select the high temperature resistant air valve with silicone gasket. The temperature is reliable when opening and closing the valve. Due to the temperature of the gas through which the valve passes, it is very easy for conventional plastic electric actuators to age and deform, resulting in ineffective execution. Generally, long rod actuators are used.