Compared with ordinary vacuum cleaners, the industrial central dust collector has a powerful dust collection function and can be cleaned quickly, avoiding secondary pollution caused by dust and noise pollution: 1. The dusty gas enters the ash hopper of each sub room from the air inlet equalizing pipe of the dust remover. The central dust removal of the workshop is customized and guided by the ash hopper guide device. 　　 2. The large particles of dust are separated and directly fall into the ash hopper, while the fine dust enters the middle box evenly and is adsorbed on the outer surface of the filter bag. Clean gas enters the upper box through the filter bag and is discharged into the atmosphere through offline valves and exhaust pipes. 　　 3. Timing or manual cleaning can be adopted: each chamber of the pulse bag filter will be cleaned in turn, and the chamber that has completed the cleaning will be restored to the dedusting state immediately. 　　 4. Open the electric control pulse valve according to the set procedure, stop air blowing, use the compressed air instantaneous blowing to increase the pressure in the filter bag, shake the dust on the filter bag into the ash bucket, and discharge it by the ash discharge mechanism. 　　 5. With the increasing dust on the outer surface of the filter bag, the differential pressure monitoring system will send a signal when the equipment resistance reaches the set value. 　　 6. The dust removal mechanism starts to work, and compressed air is sprayed from the pulse valve, and then shot into the filter bag through the blowing pipe and nozzle. The filter bag expands and vibrates instantaneously, so that the dust on the surface is removed and dropped into the ash hopper, which is discharged by the ash discharge valve. 　　 7. With the progress of filtering conditions, the dust on the filter bag will accumulate more and more. When the equipment resistance reaches the limited resistance value, the ash removal control device will automatically close the offline valve of one chamber according to the differential pressure setting value or the ash removal time setting value.

The catalytic combustion equipment for waste gas treatment is mainly used as a supporting part of the catalytic bed electric heating oxidation combustion system in the CO/RCO adsorption+desorption+catalytic combustion system. It is widely applicable to the purification and odor elimination of hazardous waste gas volatilized or leaked from painting, printing, household appliances, footwear, plastics and various chemical workshops, and is suitable for low concentration (1501000) The organic waste gas that is not suitable for direct combustion or catalytic combustion and recovery treatment will be concentrated by activated carbon adsorption, and then the high concentration organic waste gas will be removed through the desorption procedure and sent to the unit for thermal oxidation reaction. The self heating effect of the organic waste gas catalytic reaction can greatly reduce the heat consumption of the electric heater, especially for the treatment sites with large air volume, Satisfactory economic and social benefits can be obtained. Application scope of exhaust gas catalytic combustion equipment: 1. Industrial applications: common pollutants discharged from petrochemical, light industry, plastics, printing, coating and other industries; 2. Waste gas type application: hydrocarbon compounds (aromatics, alkanes, olefins), benzene, ketones, phenols, alcohols, ethers, alkanes and other compounds; Features of catalytic combustion equipment for waste gas treatment: 1. Convenient operation: fully automatic control during operation. 2. Low energy consumption: during normal operation, the equipment operates at low power (or no power) because the exhaust gas has some concentration. 3. Stable performance: pressure relief and self protection, fire resistance and dust removal, over temperature alarm and automatic control. 4. Low resistance: honeycomb ceramic catalyst impregnated with today's advanced precious metal palladium and platinum has a large specific surface area. 5. Small floor area: only 70% of the same products in the same industry. 6. Long service life: the catalyst is usually replaced within 4 years

Microwave and ultraviolet water treatment equipment can improve heat exchange efficiency, save energy and reduce consumption. new type Microwave drying The deposits on the surface of the cooler rise by 0. mm every time, High efficiency of heat exchanger can generally reduce 20-30%, and power consumption will increase 4-8%. The selection of organic chemical dosing method can maintain the equipment and extend the service life of the equipment. The etching rate of carbon steel by cooling circulating water without microwave ultraviolet water treatment equipment exceeds 0.5mm/a, Microwave drying manufactor The corrosion rate of the solved cooling circulating water on carbon steel is less than 0. mm/a, which can reasonably maintain the equipment and extend the service life of the equipment. Reduce the frequency of routine maintenance to ensure normal operation.

Microwave electrodeless ultraviolet sterilization equipment has high value in microwave ultraviolet water treatment equipment, new type Microwave drying It destroys and changes the structure of DNA of microorganisms through the irradiation of ultraviolet light, so that the bacteria will die immediately or cannot reproduce, so as to achieve the purpose of sterilization. The real bactericidal effect is UVC ultraviolet, Microwave drying manufactor Because C-band ultraviolet light is easily absorbed by the DNA of organisms, the ultraviolet light of about 253.7 nm is preferred. It is a pure physical disinfection method, which has the advantages of simplicity, convenience, broad-spectrum, no secondary pollution, convenient management and automation. With the introduction of various new designed ultraviolet lamps, the application range of ultraviolet sterilization is also expanding.

Microwave electrodeless ultraviolet sterilization equipment focuses on "ultraviolet". Through the role of ultraviolet, it mainly uses 254 nm ultraviolet light. This wavelength of ultraviolet light, even with a small amount of ultraviolet radiation, can damage a cell's life core - DNA, thus preventing cell regeneration, new type Microwave drying Loss of regenerative capacity makes bacteria harmless, thus achieving sterilization effect. In order to ensure that no microorganisms can be detected in the product, ultraviolet disinfection can be used, which is a non chemical disinfection method, Microwave drying manufactor Ultraviolet rays will not introduce toxins or residues in water, and will not change the chemical composition, taste, odor/PH value of the liquid to be disinfected.