The microwave ultraviolet water treatment equipment adopts filters with multiple filter layers, whose primary purpose is to remove the sediment, rust, colloidal substances, suspended solids and other substances with particles of more than 20um in the raw water, Customized Microwave cleaning equipment Manual valve control or full-automatic controller can be selected for a series of operations such as back flushing and forward flushing. Ensure the quality of water produced by the equipment, and extend the service life of microwave and ultraviolet water treatment equipment manufacturers. Microwave cleaning equipment programme Check whether the power is cut off and the plug is firmly inserted. Check whether the wiring plug of the low-voltage switch of the microwave ultraviolet water treatment equipment falls or fails to work so that the power contact cannot return. Check whether the connecting wire of each terminal falls off, and check whether the water pressure of tap water is too low, so that the low-voltage switch does not work.

The UV sterilization equipment occupies a small area and the structure requirements are simple, so the total investment is small, Customized Microwave cleaning equipment The cost of operation is also low. At the level of thousand tons of microwave ultraviolet water treatment equipment, its cost is only 1/2 of chlorine disinfection. Microwave electrodeless ultraviolet sterilization equipment can be used in secondary water supply of high-rise buildings, electronics, medicine, food, chemical industry, beverage, cosmetics industry to produce pure water, swimming pool water disinfection and other water disinfection fields, Microwave cleaning equipment programme Its disinfection process includes tap water → quartz sand filter → activated carbon filter → precision filter → reverse osmosis membrane → ultraviolet disinfection system → ultrafiltration device → water tank, which has the advantages of simplicity, convenience, broad-spectrum, no secondary pollution, easy management and automation.

Activated carbon adsorption and catalytic combustion equipment is a common volatile organic waste gas treatment equipment. It is energy-saving, environmental protection, no secondary pollution, and high purification efficiency. It is a very good equipment for VOC waste gas treatment. Generally, the main components of activated carbon adsorption catalytic combustion equipment are as follows: Pretreatment equipment: since honeycomb activated carbon adsorption requires specific conditions such as temperature, humidity and cleanliness, it is necessary to treat the organic waste gas with different characteristics before entering the activated carbon adsorption. The organic waste gas containing more dust particles needs to be filtered. The waste gas with a temperature greater than 45 ℃ needs to be cooled, and the waste gas containing a large number of water mist particles needs to be separated and filtered. Activated carbon adsorption bed: it can absorb organic waste gas by taking advantage of the porous physical characteristics of activated carbon. The design of the adsorption bed follows the law of two-phase adsorption curve. Only by combining the amount of activated carbon and calculating the cross section wind speed and retention time of activated carbon adsorption can the adsorption efficiency meet the design requirements and meet the emission standards. The box is in negative pressure state during equipment operation, and it is required to be air tight. The desorption temperature of the box is between 70-100 ℃ during the desorption process, and the heat preservation is generally 50mm considering the energy saving and safety factors. Ensure that the temperature of the outer wall of the box is not higher than the normal temperature by 15 ℃. Main exhaust fan: as the main power of the equipment, the exhaust fan guides the air to move according to the specified process. The fan can be selected accurately only when it is stable and reliable, and the resistance calculation of the system is accurate. The operation of the fan will produce noise, and the high-power fan needs to be equipped with a sound insulation room. Attention shall be paid to the design that the wind speed at the air outlet shall not be too high. Catalytic combustion equipment: after the system has operated for a period of time, the activated carbon needs to be regenerated after adsorption saturation to restore the adsorption activity of the activated carbon. The organic waste gas is concentrated in the activated carbon. After the organic matter is separated from the activated carbon layer at low temperature, it is decomposed into water and carbon dioxide at about 300 ℃ through the action of catalyst. At the same time, the energy is released. The energy is replaced by the heat exchange device to maintain the energy of spontaneous combustion of the equipment. For a single activated carbon adsorption bed, the desorption time is 2-2.5 hours. The set time of activated carbon adsorption box is automatically switched to desorption regularly. The service life of the ceramic honeycomb noble metal catalyst loaded inside is 8000 hours. The whole desorption system adopts multi-point temperature control to ensure the stability of desorption effect. The selection of organic waste gas catalyst is the core of this equipment. Valve switching system: valves include adsorption system valve, desorption system valve, cooling and emergency discharge valve. The three types of valves are required to be timely and accordingly to ensure that the air leakage rate is less than 2%. The conventional galvanized sheet air valve in the market has air leakage due to unreliable sealing, so it is necessary to select the high temperature resistant air valve with silicone gasket. The temperature is reliable when opening and closing the valve. Due to the temperature of the gas through which the valve passes, it is very easy for conventional plastic electric actuators to age and deform, resulting in ineffective execution. Generally, long rod actuators are used.

Microwave electrodeless ultraviolet sterilization equipment has high value in microwave ultraviolet water treatment equipment, Customized Microwave cleaning equipment It destroys and changes the structure of DNA of microorganisms through the irradiation of ultraviolet light, so that the bacteria will die immediately or cannot reproduce, so as to achieve the purpose of sterilization. The real bactericidal effect is UVC ultraviolet, Microwave cleaning equipment programme Because C-band ultraviolet light is easily absorbed by the DNA of organisms, the ultraviolet light of about 253.7 nm is preferred. It is a pure physical disinfection method, which has the advantages of simplicity, convenience, broad-spectrum, no secondary pollution, convenient management and automation. With the introduction of various new designed ultraviolet lamps, the application range of ultraviolet sterilization is also expanding.

I. Efficient deodorization II. No substances need to be added III. Strong adaptability IV. Low operation cost V. No treatment VI. Small area of equipment VII. Manufacturing of high-quality imported materials