1. The welding of equipment shell and framework shall be firm without obvious deformation or burn through defects. 2. The equipment surface shall be evenly sprayed with the same color, and the surface shall be free of flow marks, bubbles, paint leakage and peeling. 3. The appearance of the equipment shall be neat and beautiful without obvious hammer marks and unevenness. The panel instruments, switches, indicator lights and labels shall be installed firmly and correctly. In order to ensure the stability of the equipment, we need to replace the lamp regularly, production Microwave extraction equipment The imported lamp should be replaced after 9000 hours of continuous service or one year to ensure a high disinfection rate. Microwave extraction equipment manufactor When replacing the lamp tube, first pull out the power socket of the lamp tube, pull out the lamp tube, then carefully insert the cleaned new lamp tube into the sterilizer, install the gasket, check for water leakage, and then plug in the power supply. Be careful not to touch the quartz glass of the new lamp tube with your fingers, otherwise the disinfection effect will be affected due to stains.

Swimming and playing other water sports are exciting ways, production Microwave extraction equipment You can relax and exercise at the same time! Some sunshine, physical exercise and laughter all advocate a healthy life. You can spend endless time in the water with your friends and family, but it is responsible to enjoy the fun in the carefree sunshine. A healthy swimming pool is not only visually clean, but also has proper chemical balance, Microwave extraction equipment manufactor These chemical balances should not overwhelm your senses. If you like swimming pools, you will hear about bacteria such as Giardia, Cryptosporidium and Legionella. Installing an ultraviolet sterilizer will eliminate the bacteria and parasites that cause these diseases, and keep your swimming pool water clear and transparent with confidence!

working principle: The thermal storage catalytic combustion equipment uses natural gas to directly burn organic waste gas. Under the temperature of 750~850 ℃, organic molecules are decomposed into CO2 and H2O. The burned flue gas accumulates heat in the ceramic through the thermal storage ceramic brick, preheats the organic waste gas, and then discharges it. The inlet and outlet directions of the waste gas are automatically switched by the switch valve, and work circularly, RTO can fully recover and burn organic decomposition heat energy, which greatly reduces the energy consumption of the system. Catalytic combustion equipment is applicable to industries: Applicable to the treatment of mixed combustible organic waste gas and odor with large and medium concentration (thousands of ppm) and medium air volume Applicable to waste gas treatment in paint shop Applicable to waste gas treatment of electronic product manufacturing and integrated circuit Applicable to waste gas treatment in printing process and injection molding process Applicable to the treatment of organic waste gas generated in petrochemical, medical and other industries Technical features of regenerative catalytic combustion equipment: Wide range of exhaust gas; High waste gas treatment efficiency; Less maintenance work, safe and reliable; Low pressure loss and high purification efficiency; Long service life of equipment; Low operation cost

Ultraviolet disinfection belongs to physical instant disinfection technology, which can keep sterile under the condition that the water body is not polluted. When the treated water leaves the disinfection reactor, production Microwave extraction equipment Some microorganisms killed by ultraviolet light will repair damaged molecules and regenerate bacteria under visible light irradiation, which is called light reactivation. Microwave extraction equipment manufactor Some bacteria can also repair themselves under the condition of no light, that is, dark reactivation. According to the current research results, photoreactivation is the main way of most microbial remediation and also the main control target.

Activated carbon adsorption and catalytic combustion equipment is a common volatile organic waste gas treatment equipment. It is energy-saving, environmental protection, no secondary pollution, and high purification efficiency. It is a very good equipment for VOC waste gas treatment. Generally, the main components of activated carbon adsorption catalytic combustion equipment are as follows: Pretreatment equipment: since honeycomb activated carbon adsorption requires specific conditions such as temperature, humidity and cleanliness, it is necessary to treat the organic waste gas with different characteristics before entering the activated carbon adsorption. The organic waste gas containing more dust particles needs to be filtered. The waste gas with a temperature greater than 45 ℃ needs to be cooled, and the waste gas containing a large number of water mist particles needs to be separated and filtered. Activated carbon adsorption bed: it can absorb organic waste gas by taking advantage of the porous physical characteristics of activated carbon. The design of the adsorption bed follows the law of two-phase adsorption curve. Only by combining the amount of activated carbon and calculating the cross section wind speed and retention time of activated carbon adsorption can the adsorption efficiency meet the design requirements and meet the emission standards. The box is in negative pressure state during equipment operation, and it is required to be air tight. The desorption temperature of the box is between 70-100 ℃ during the desorption process, and the heat preservation is generally 50mm considering the energy saving and safety factors. Ensure that the temperature of the outer wall of the box is not higher than the normal temperature by 15 ℃. Main exhaust fan: as the main power of the equipment, the exhaust fan guides the air to move according to the specified process. The fan can be selected accurately only when it is stable and reliable, and the resistance calculation of the system is accurate. The operation of the fan will produce noise, and the high-power fan needs to be equipped with a sound insulation room. Attention shall be paid to the design that the wind speed at the air outlet shall not be too high. Catalytic combustion equipment: after the system has operated for a period of time, the activated carbon needs to be regenerated after adsorption saturation to restore the adsorption activity of the activated carbon. The organic waste gas is concentrated in the activated carbon. After the organic matter is separated from the activated carbon layer at low temperature, it is decomposed into water and carbon dioxide at about 300 ℃ through the action of catalyst. At the same time, the energy is released. The energy is replaced by the heat exchange device to maintain the energy of spontaneous combustion of the equipment. For a single activated carbon adsorption bed, the desorption time is 2-2.5 hours. The set time of activated carbon adsorption box is automatically switched to desorption regularly. The service life of the ceramic honeycomb noble metal catalyst loaded inside is 8000 hours. The whole desorption system adopts multi-point temperature control to ensure the stability of desorption effect. The selection of organic waste gas catalyst is the core of this equipment. Valve switching system: valves include adsorption system valve, desorption system valve, cooling and emergency discharge valve. The three types of valves are required to be timely and accordingly to ensure that the air leakage rate is less than 2%. The conventional galvanized sheet air valve in the market has air leakage due to unreliable sealing, so it is necessary to select the high temperature resistant air valve with silicone gasket. The temperature is reliable when opening and closing the valve. Due to the temperature of the gas through which the valve passes, it is very easy for conventional plastic electric actuators to age and deform, resulting in ineffective execution. Generally, long rod actuators are used.