During the installation of the microwave and ultraviolet water treatment equipment, the commissioning shall be carried out continuously, production Microwave drying equipment A lot of work needs to be completed before installation. For example, some of their installations must meet the final installation standards and have the final acceptance standards, so that there can be more ways to deal with it, Microwave drying equipment programme The operation shall be carried out according to the relevant design requirements as far as possible, and all operations can be accepted during the operation process, so as to ensure the actual use.

Activated carbon adsorption and catalytic combustion equipment is a common volatile organic waste gas treatment equipment. It is energy-saving, environmental protection, no secondary pollution, and high purification efficiency. It is a very good equipment for VOC waste gas treatment. Generally, the main components of activated carbon adsorption catalytic combustion equipment are as follows: Pretreatment equipment: since honeycomb activated carbon adsorption requires specific conditions such as temperature, humidity and cleanliness, it is necessary to treat the organic waste gas with different characteristics before entering the activated carbon adsorption. The organic waste gas containing more dust particles needs to be filtered. The waste gas with a temperature greater than 45 ℃ needs to be cooled, and the waste gas containing a large number of water mist particles needs to be separated and filtered. Activated carbon adsorption bed: it can absorb organic waste gas by taking advantage of the porous physical characteristics of activated carbon. The design of the adsorption bed follows the law of two-phase adsorption curve. Only by combining the amount of activated carbon and calculating the cross section wind speed and retention time of activated carbon adsorption can the adsorption efficiency meet the design requirements and meet the emission standards. The box is in negative pressure state during equipment operation, and it is required to be air tight. The desorption temperature of the box is between 70-100 ℃ during the desorption process, and the heat preservation is generally 50mm considering the energy saving and safety factors. Ensure that the temperature of the outer wall of the box is not higher than the normal temperature by 15 ℃. Main exhaust fan: as the main power of the equipment, the exhaust fan guides the air to move according to the specified process. The fan can be selected accurately only when it is stable and reliable, and the resistance calculation of the system is accurate. The operation of the fan will produce noise, and the high-power fan needs to be equipped with a sound insulation room. Attention shall be paid to the design that the wind speed at the air outlet shall not be too high. Catalytic combustion equipment: after the system has operated for a period of time, the activated carbon needs to be regenerated after adsorption saturation to restore the adsorption activity of the activated carbon. The organic waste gas is concentrated in the activated carbon. After the organic matter is separated from the activated carbon layer at low temperature, it is decomposed into water and carbon dioxide at about 300 ℃ through the action of catalyst. At the same time, the energy is released. The energy is replaced by the heat exchange device to maintain the energy of spontaneous combustion of the equipment. For a single activated carbon adsorption bed, the desorption time is 2-2.5 hours. The set time of activated carbon adsorption box is automatically switched to desorption regularly. The service life of the ceramic honeycomb noble metal catalyst loaded inside is 8000 hours. The whole desorption system adopts multi-point temperature control to ensure the stability of desorption effect. The selection of organic waste gas catalyst is the core of this equipment. Valve switching system: valves include adsorption system valve, desorption system valve, cooling and emergency discharge valve. The three types of valves are required to be timely and accordingly to ensure that the air leakage rate is less than 2%. The conventional galvanized sheet air valve in the market has air leakage due to unreliable sealing, so it is necessary to select the high temperature resistant air valve with silicone gasket. The temperature is reliable when opening and closing the valve. Due to the temperature of the gas through which the valve passes, it is very easy for conventional plastic electric actuators to age and deform, resulting in ineffective execution. Generally, long rod actuators are used.

RCO organic waste gas catalytic combustion purification equipment can effectively purify the environment, pollution, improve labor operating conditions, ensure the health of workers, and the heat emitted can be recycled to reduce production costs. RCO organic waste gas catalytic combustion equipment has perfect system design, complete auxiliary equipment, high purification efficiency and high automation. RCO organic waste gas catalytic combustion equipment RCO organic waste gas catalytic combustion purification device is designed based on two basic principles of adsorption and catalytic combustion, namely adsorption concentration catalytic combustion method. The dedusting equipment adopts the working mode of single bed adsorption purification of organic waste gas and catalytic combustion device regeneration and activation of activated carbon. Firstly, the organic waste gas with low concentration is adsorbed by activated carbon, and the adsorption operation is stopped when it is almost saturated, then the organic matter is desorbed from the activated carbon by hot gas flow to regenerate the activated carbon; The desorbed organic matter has been concentrated (the concentration is dozens of times higher than the original) and sent to the catalytic combustion chamber for catalytic conversion into CO2 and H2O for emission; When the concentration of organic waste gas reaches above 2000ppm, the organic waste gas can maintain spontaneous combustion in the catalytic bed without external heating. Some of the burned tail gas is discharged into the atmosphere, and most of it is sent to the adsorption bed for desorption and regeneration of activated carbon. In this way, the heat energy required for combustion and desorption can be met to save energy. The regenerated activated carbon can be used for the next adsorption.? RCO organic waste gas catalytic combustion equipment uses catalytic combustion method to convert toxic and harmful organic gas into non-toxic gas.? The main structure of RCO organic waste gas catalytic combustion equipment is composed of three major parts: purification device host, induced draft fan and control system. The catalytic combustion purification device includes: dedusting flame arrester, heat exchanger, preheater and catalytic combustion chamber. The organic waste gas enters the preprocessor from the air inlet at the upper part of the equipment, passes through the coarse filter element composed of multi-layer stainless steel wire mesh to remove dust and other particles in the waste gas, and enters the combined adsorption bed from the main channel at the lower part of the device (two rows in parallel with six grids). Each adsorption bed is equipped with a set of pneumatic switch valve, which can change the adsorption bed into adsorption/desorption state. The longitudinal section of the adsorption bed from bottom to top is respectively the inlet manifold, adsorption chamber, air purification chamber and outlet manifold. The adsorption chamber and the air purification chamber are separated by a flower plate, under which a number of adsorption cylinders are hoisted. The waste gas entering the adsorption chamber passes through the adsorption layer through the outer wall of the adsorption cylinder, VOCs are adsorbed by a large number of microporous surfaces of the adsorbent, and the waste gas is purified and then enters the air purification chamber upward through the flower plate holes, Then it enters the main outlet pipe through the switching valve and is discharged by the fan. One of the six adsorption chambers must be in the desorption state, and the other five must be in the adsorption state. Generally, the desorption time is 12 minutes, that is, the adsorption bed responsible for the adsorption work can be desorbed and regenerated once every hour. This work process of the device coincides with the name of the invention zhuanli - a kind of compartment offline desorption bag type adsorption equipment. Its process principle is the same as that of the pulse reverse blow compartment offline bag type dust collector, except that the purification process of the device is "physical adsorption", The bag filter purification process is "physical filtration". The desorption working medium of the adsorption bed is hot air, which is provided by the catalytic combustion device. Generally, the temperature of the hot air is ≤ 150 ℃, which is determined by the boiling point of different VOCs and the saturated vapor partial pressure at the desorption temperature.

In the daily treatment of sewage, many people think that sewage management needs high costs, so they improve on the basis of sewage ultraviolet disinfection equipment in large cities. But suburban residents or residents far away from the city center are often excluded because the pipeline design is not perfect, production Microwave drying equipment They will be discharged indiscriminately, resulting in more serious urban pollution. Microwave drying equipment programme At present, the public's attention to microwave and ultraviolet water treatment equipment for pollution, coupled with the adjustment of China's and cities' systems, supervises urban emissions and investment in microwave and ultraviolet water treatment equipment for urban pollution. The emergence of ultraviolet disinfection equipment for domestic sewage makes the public not only find that the investment cost is low, but also the treatment efficiency is relatively high.

The technology of microwave ultraviolet water treatment equipment is to use double layer ultrafiltration membrane for microwave ultraviolet water treatment equipment, or combine ultrafiltration membrane and reverse osmosis filtration membrane for application. Microwave drying equipment programme When the manufacturer of microwave ultraviolet water treatment equipment applies external pressure on the concentrated solution side, the penetration speed will decrease. When the pressure increases to a certain value, the penetration process will stop and the so-called penetration balance will be reached. The external pressure under the balance condition is called the penetration pressure. When the pressure on the concentrated solution side continues to increase, that is, when the applied pressure is greater than the penetration pressure, The solvent of purified water equipment will reverse its original soaking direction and enter the dilute solution side from the concentrated solution side through the semi permeable membrane, production Microwave drying equipment This phenomenon is called reverse osmosis. For a long time, it will not only affect the effluent quality of the equipment, but also lead to the fouling of the reverse osmosis membrane of the main components of the equipment, resulting in the small output of the pure water equipment, the substandard effluent quality, or the equipment can not be used. In order to ensure the continuous and safe operation of pure water equipment, the maintenance of pure water equipment is very important.

Integrated equipment for multistage lampblack purification Application industry: large canteens and community lampblack purification solutions adopt root cause treatment, one-step, deodorization purification, brake cleaning, intelligent monitoring, intelligent control, and the lampblack purification rate exceeds 98%, exceeding the landmark and international emission standards.