Microwave electrodeless ultraviolet sterilization equipment has high value in microwave ultraviolet water treatment equipment, new type Breeding sterilization and disinfection equipment It destroys and changes the structure of DNA of microorganisms through the irradiation of ultraviolet light, so that the bacteria will die immediately or cannot reproduce, so as to achieve the purpose of sterilization. The real bactericidal effect is UVC ultraviolet, Breeding sterilization and disinfection equipment manufactor Because C-band ultraviolet light is easily absorbed by the DNA of organisms, the ultraviolet light of about 253.7 nm is preferred. It is a pure physical disinfection method, which has the advantages of simplicity, convenience, broad-spectrum, no secondary pollution, convenient management and automation. With the introduction of various new designed ultraviolet lamps, the application range of ultraviolet sterilization is also expanding.

In the microwave and ultraviolet water treatment equipment, the reverse osmosis equipment needs three kinds of sealing rings to realize the sealing barrier of each part of the membrane shell. In order to reduce the resistance of the device, water or glycerin should be added to the surface of the sealing ring. new type Breeding sterilization and disinfection equipment Microwave ultraviolet water treatment equipment PP cotton softening equipment. Breeding sterilization and disinfection equipment manufactor Special attention should be paid to the use of petroleum jelly or other petroleum grease lubricants as lubricants. Otherwise, the fresh water pipeline will crack, especially the expansion of the sealant ring. The expansion of the skirt does not directly affect the operation of the system, but will affect the reloading of the system after unloading, that is, the expansion skirt is difficult to enter the slot during loading.

Activated carbon adsorption and catalytic combustion equipment is a common volatile organic waste gas treatment equipment. It is energy-saving, environmental protection, no secondary pollution, and high purification efficiency. It is a very good equipment for VOC waste gas treatment. Generally, the main composition of activated carbon adsorption catalytic combustion equipment is as follows: Pretreatment equipment: since honeycomb activated carbon adsorption requires specific conditions such as temperature, humidity and cleanliness, it is necessary to treat the organic waste gas with different characteristics before entering the activated carbon adsorption. The organic waste gas containing more dust particles needs to be filtered. The waste gas with a temperature greater than 45 ℃ needs to be cooled, and the waste gas containing a large number of water mist particles needs to be separated and filtered. Activated carbon adsorption bed: it can absorb organic waste gas by taking advantage of the porous physical characteristics of activated carbon. The design of the adsorption bed follows the law of two-phase adsorption curve. Only by combining the amount of activated carbon and calculating the cross section wind speed and retention time of activated carbon adsorption can the adsorption efficiency meet the design requirements and meet the emission standards. The box is in negative pressure state during equipment operation, and it is required to be air tight. The desorption temperature of the box is between 70-100 ℃ during the desorption process, and the heat preservation is generally 50mm considering the energy saving and safety factors. Ensure that the temperature of the outer wall of the box is not higher than the normal temperature by 15 ℃. Main exhaust fan: as the main power of the equipment, the exhaust fan guides the air to move according to the specified process. The fan can be selected accurately only when it is stable and reliable, and the resistance calculation of the system is accurate. The operation of the fan will produce noise, and the high-power fan needs to be equipped with a sound insulation room. Attention shall be paid to the design that the wind speed at the air outlet shall not be too high. Catalytic combustion equipment: after the system has operated for a period of time, the activated carbon needs to be regenerated after adsorption saturation to restore the adsorption activity of the activated carbon. The organic waste gas is concentrated in the activated carbon. After the organic matter is separated from the activated carbon layer at low temperature, it is decomposed into water and carbon dioxide at about 300 ℃ through the action of the catalyst. At the same time, the energy is released. The energy is replaced by the heat exchange device to maintain the energy of equipment spontaneous combustion. For a single activated carbon adsorption bed, the desorption time is 2-2.5 hours. The set time of activated carbon adsorption box is automatically switched to desorption regularly. The service life of the ceramic honeycomb noble metal catalyst loaded inside is 8000 hours. The whole desorption system adopts multi-point temperature control to ensure the stability of desorption effect. The selection of organic waste gas catalyst is the core of this equipment. Valve switching system: valves include adsorption system valve, desorption system valve, cooling and emergency discharge valve. The three types of valves are required to be timely and accordingly to ensure that the air leakage rate is less than 2%. The conventional galvanized sheet air valve in the market has air leakage due to unreliable sealing, so it is necessary to select the high temperature resistant air valve with silicone gasket. The temperature is reliable when opening and closing the valve. Due to the temperature of the gas through which the valve passes, it is very easy for conventional plastic electric actuators to age and deform, resulting in ineffective execution. Generally, long rod actuators are used.

Most of the microwave ultraviolet water treatment equipment is installed in the plant, but some are installed outdoors. When winter comes, the temperature also drops to below zero. Because the volume of water will increase significantly in the process of solidification and freezing, new type Breeding sterilization and disinfection equipment Once the microwave and ultraviolet water treatment equipment and pipeline are iced, it will cause the water flowing part of the equipment and pipeline to break, resulting in economic losses. Then let's see how to maintain the microwave ultraviolet water treatment equipment in winter. Breeding sterilization and disinfection equipment manufactor In order to increase the effective thermal insulation measures for outdoor microwave ultraviolet water treatment equipment and pipes, straw rope wrapped with plastic film can be used for thermal insulation, or 1.2-1.5cm thick insulation cotton or insulation cotton pipe can be used for tape wrapping.