With the extension of the use time of the clean microwave ultraviolet water treatment equipment, it is a normal phenomenon that the water production decreases. The decrease of water production in winter is due to the decrease of water temperature and permeability, and the change of reverse osmosis membrane density. These two reasons will reduce the water production of microwave and ultraviolet water treatment equipment. Strengthen pretreatment device, new type Industrial kiln Increasing the cleaning time, replacing the filter element frequently, backwashing the reverse osmosis membrane in time, and extending the interval are all ways to promote the normal operation of the microwave ultraviolet water treatment equipment. Industrial kiln manufactor If the water pipe or microwave ultraviolet water treatment equipment is frozen, the valve shall be closed in time, wrapped with towel, and slowly watered with warm water. Do not directly use fire for barbecue, nor use boiling water for heating, so as to prevent the microwave and ultraviolet water treatment equipment and pipes from cracking, or use a hair dryer to dry them. At the same time, gently tap hard objects on the water pipe until the pipe freezes and thaws, and the tap water flows out smoothly. If the fully automatic frequency conversion water supply equipment has been frozen, it can only be wrapped with a hot towel and sprinkled with warm water until the pipe freezes and thaws, so that the water can flow out smoothly.

The power supply is the foundation and should be used carefully. Generally, it needs to work under 200V/50Hz AC power, new type Industrial kiln In order to ensure the correct operation of the complete set of automatic water softening device. Industrial kiln manufactor The manufacturer of the microwave and ultraviolet water treatment equipment shall ensure that the power cannot be cut off, and that the switch of the equipment cannot be cut to the point, so as to prevent the quality problems of the softening microwave and ultraviolet water treatment equipment and the increase of equipment loss.

Compared with ordinary vacuum cleaners, the industrial central dust collector has a powerful dust collection function and can be cleaned quickly, avoiding secondary pollution caused by dust and noise pollution: 1. The dusty gas enters the ash hopper of each sub room from the air inlet equalizing pipe of the dust remover. The central dust removal of the workshop is customized and guided by the ash hopper guide device. 　　 2. The large particles of dust are separated and directly fall into the ash hopper, while the fine dust enters the middle box evenly and is adsorbed on the outer surface of the filter bag. Clean gas enters the upper box through the filter bag and is discharged into the atmosphere through offline valves and exhaust pipes. 　　 3. Timing or manual cleaning can be adopted: each chamber of the pulse bag filter will be cleaned in turn, and the chamber that has completed the cleaning will be restored to the dedusting state immediately. 　　 4. Open the electric control pulse valve according to the set procedure, stop air blowing, use the compressed air instantaneous blowing to increase the pressure in the filter bag, shake the dust on the filter bag into the ash bucket, and discharge it by the ash discharge mechanism. 　　 5. With the increasing dust on the outer surface of the filter bag, the differential pressure monitoring system will send a signal when the equipment resistance reaches the set value. 　　 6. The dust removal mechanism starts to work, and compressed air is sprayed from the pulse valve, and then shot into the filter bag through the blowing pipe and nozzle. The filter bag expands and vibrates instantaneously, so that the dust on the surface is removed and dropped into the ash hopper, which is discharged by the ash discharge valve. 　　 7. With the progress of filtering conditions, the dust on the filter bag will accumulate more and more. When the equipment resistance reaches the limited resistance value, the ash removal control device will automatically close the offline valve of one chamber according to the differential pressure setting value or the ash removal time setting value.

UV disinfection is generally only used for air and instrument surface disinfection. Surgical dressings cannot be treated by UV radiation as a routine method. Ultraviolet radiation is the general term of radiation in electromagnetic spectrum with wavelength from 10nm to 400nm, which can not cause people's vision. In 1801, German physicist Ritter found that the ultraviolet ray could sensitize the photographic negative containing silver bromide at the outer part of the ultraviolet end of the sunlight spectrum, so he found the existence of ultraviolet ray. Too much ultraviolet rays entering the body will cause skin cancer. new type Industrial kiln It can be disinfected after use every day. It should be disinfected two or three times a week. It is recommended that the toothbrush head should be replaced every three months. It can be disinfected every day. The SEGA toothbrush sterilizer I selected should be disinfected for 6-8 minutes each time. It is a good ultraviolet disinfection lamp. It needs to be equipped with a ballast. Mould formation is due to long-term lack of ventilation and humidity, Industrial kiln manufactor If ventilation and moisture removal are available, mold will not grow. Since mold has been formed, first kill it with a mold remover, and then put a moisture bag such as a charcoal bag. I often do on-site mildew and odor removal projects. You can sprinkle lime on the corner of the wall or place charcoal in the house to absorb moisture when the house is wet. In addition, don't open the window in foggy or rainy weather. Open the window in good weather to ventilate in time.

VOCS catalytic combustion waste gas treatment equipment in paint shop: Catalytic combustion equipment is a kind of deodorization and deodorization waste gas treatment equipment. The concept of catalytic combustion is to use the catalytic incineration reaction of combustibles under the effect of catalyst and certain temperature conditions. Combustibles are burned under the effect of catalyst. Compared with direct incineration, catalytic incineration has a lower temperature and is quite safe. Catalytic principle and equipment composition (1) Catalyst is defined as a substance that can improve the rate of chemical reaction, control the direction of reaction, and keep its chemical properties unchanged before and after reaction. (2) The mechanism of catalytic effect The mechanism of catalytic effect is a very complicated problem, which is only briefly introduced here. In a chemical reaction process, the participation of the catalyst cannot change the original chemical balance, but only the speed of the chemical reaction. Before and after the reaction, the nature of the catalyst itself does not change. So, how does the catalyst speed up the response? The catalyst has not changed before and after the reaction, so has the catalyst participated in the reaction? In practice, the catalyst itself has participated in the reaction. It is because of its participation that the reaction has changed the original path, reduced the activation energy, and then accelerated the reaction speed. For example, the reaction A+B → C is transited through the central active complex (AB), that is, the reaction speed of A+B → [AB] → C is slow. After participating in catalyst K, the reaction is completed in an easy way: A+B+2K → [AK]+[BK] → [CK]+K → C+2K center no longer needs the transition from [AB] to C, and then the reaction speed is accelerated without changing the catalyst properties. (3) Process composition of catalytic incineration equipment: different emission occasions and different exhaust gases have different process flows. However, no matter which process flow is adopted, it is composed of the following process units. ① Waste gas pretreatment In order to avoid blocking of the catalyst bed and catalyst poisoning, it is necessary to pretreat the waste gas before entering the bed to remove the dust, droplets and catalyst poisons in the waste gas. ② Preheating equipment Preheating equipment includes waste gas preheating equipment and catalyst incinerator preheating equipment. Because all catalysts have a catalytic activity temperature, it is called catalyst ignition temperature for catalytic incineration. It is necessary to make the temperature of exhaust gas and bed reach the ignition temperature before catalytic incineration. Therefore, it is necessary to set up preheating equipment. However, for occasions where the exhaust gas temperature is high, such as enameled wire, insulating material, baking varnish, etc., and the temperature can reach more than 300 ℃, preheating equipment is not required. The hot gas heated by the preheating equipment can be arranged in the heat exchanger and bed. The heat source of the preheater can be flue gas or electric heating, and now electric heating is more used. When catalytic reaction starts, exhaust gas can be preheated with recovered reaction heat as far as possible. In the case of high reaction heat, waste heat recovery equipment should also be set to save power. The heat source temperature of preheated exhaust gas generally exceeds the catalyst activity temperature. In order to maintain the catalyst, the heating equipment should be kept a certain distance from the catalytic incineration equipment, so that the exhaust gas temperature can be evenly distributed. Starting from the need for preheating, catalytic incineration is applicable to the purification of continuous exhaust. If intermittent exhaust, not only each preheating needs energy, but also the reaction heat can not be recycled, which will result in great power waste. This should be noted in planning and selection. ③ Fixed bed catalytic reverberator is generally selected as catalytic incineration equipment. The planning of the reverberator shall be carried out according to the standard, which shall be convenient for operation, repair and catalyst loading and unloading. In the process planning of catalytic incineration, it is necessary to plan the built-up process of components according to the specific situation in the case of large air volume, that is, the preheater and the reverberator are installed separately, and the pipes are connected between them. For occasions with small air volume, catalytic incinerators can be selected to combine preheating and reaction, but pay attention to the distance between preheating section and reaction section. In the catalytic incineration of organic waste gas, the organic waste gas to be treated is easy to explode when mixed with air at high temperature, so the safety problem is very important. Therefore, on the one hand, it is necessary to control the mixing ratio of organic matter and air to keep it at the lower explosive limit; On the other hand, the catalytic incineration system should be equipped with monitoring and alarm equipment and explosion-proof measures.