新上海sh419

 Microwave ultraviolet water treatment equipment
Your current location: home page > Hot information

contact us Contact Us

Shandong Dehai Weilang Energy Equipment Co., Ltd

Contact: Mr. Wang

Tel.: 13001718597

Tel.: 0531-88551699

Email: [email protected]

Address: No. 6, Weihua West Road, Shizhong District, Jinan

Yingkou Production of Ultraviolet Sterilization Equipment Scheme

2023-12-31
 Yingkou Production of Ultraviolet Sterilization Equipment Scheme

Ultraviolet is a kind of light wave invisible to the naked eye, which exists outside the ultraviolet end of the spectrum, so it is called ultraviolet. Ultraviolet radiation is one of the electromagnetic waves from the sun, and it is usually divided into four categories according to the wavelength. The following is a special form of material operation, which is a particle stream with disconnected particles. Each UV photon with a wavelength of 253.7 nm has an energy of 4.9 eV. production Ultraviolet sterilization equipment When ultraviolet rays irradiate microorganisms, energy transfer and accumulation will occur, and the accumulation results in the inactivation of microorganisms, thus achieving the purpose of disinfection. When bacteria and viruses absorb more than 3600~65000uW/cm2, it has a strong destructive power to DNA and RNA of bacteria and viruses, Ultraviolet sterilization equipment programme It can make bacteria and viruses lose their viability and fecundity, and then eliminate bacteria and viruses to achieve disinfection and sterilization effect. On the one hand, ultraviolet light can mutate nucleic acids, hinder their replication, transcriptional blockade and protein synthesis; On the other hand, the production of free radicals can cause photoionization, which will lead to cell death.

 Yingkou Production of Ultraviolet Sterilization Equipment Scheme

1. The welding of equipment shell and framework shall be firm without obvious deformation or burn through defects. 2. The equipment surface shall be evenly sprayed with the same color, and the surface shall be free of flow marks, bubbles, paint leakage and peeling. 3. The appearance of the equipment shall be neat and beautiful without obvious hammer marks and unevenness. The panel instruments, switches, indicator lights and labels shall be installed firmly and correctly. In order to ensure the stability of the equipment, we need to replace the lamp regularly, production Ultraviolet sterilization equipment The imported lamp should be replaced after 9000 hours of continuous service or one year to ensure a high disinfection rate. Ultraviolet sterilization equipment programme When replacing the lamp tube, first pull out the power socket of the lamp tube, pull out the lamp tube, then carefully insert the cleaned new lamp tube into the sterilizer, install the gasket, check for water leakage, and then plug in the power supply. Be careful not to touch the quartz glass of the new lamp tube with your fingers, otherwise the disinfection effect will be affected due to stains.

 Yingkou Production of Ultraviolet Sterilization Equipment Scheme

I. Efficient deodorization II. No substances need to be added III. Strong adaptability IV. Low operation cost V. No treatment VI. Small area of equipment VII. Manufacturing of high-quality imported materials

 Yingkou Production of Ultraviolet Sterilization Equipment Scheme

The trapezoidal structure made of food grade transparent silica gel and special mold is used to prevent water leakage caused by improper installation. Ultraviolet sterilization equipment programme UV irradiation intensity sensor/UV irradiation intensity monitor: The UV irradiation intensity sensor can monitor the output intensity of the UV disinfection system in real time online, and output mixed signals of 0-5V or 4-20mA for use by the monitor. production Ultraviolet sterilization equipment The ultraviolet radiation intensity monitor receives the signal provided by the sensor, and can set the radiation intensity alarm value and lamp life according to the requirements. Monitor the system in real time to ensure the normal operation of the equipment.

 Yingkou Production of Ultraviolet Sterilization Equipment Scheme

To solve the problem of light reactivation: open the channel to realize underground water outflow, to avoid or reduce the visibility of treated water before entering the pipeline. At the same time, use a dark container containing a sample of test water, production Ultraviolet sterilization equipment It shall be sent for inspection in time to avoid factors such as storage conditions or test time affecting the test results. Improve the light transmittance: adjust the front-end treatment process to reduce the SS mass concentration of water in the UV disinfection device, Ultraviolet sterilization equipment programme The ultraviolet disinfection I was adjusted to ozone decolorization, which reduced the chromaticity of the influent water to ensure that SS was controlled below 10 mg/L; The front-end technology has been adjusted to strictly control the consumption of PAM and other chemicals, and a defoaming device has been installed at the water inlet of the external disinfection device to reduce the foam content in the water body and increase the light transmittance of the water body.

 Yingkou Production of Ultraviolet Sterilization Equipment Scheme

UV disinfection is generally only used for air and instrument surface disinfection. Surgical dressings cannot be treated by UV radiation as a routine method. Ultraviolet radiation is the general term of radiation in electromagnetic spectrum with wavelength from 10nm to 400nm, which can not cause people's vision. In 1801, German physicist Ritter found that the ultraviolet ray could sensitize the photographic negative containing silver bromide at the outer part of the ultraviolet end of the sunlight spectrum, so he found the existence of ultraviolet ray. Too much ultraviolet rays entering the body will cause skin cancer. production Ultraviolet sterilization equipment It can be disinfected after use every day. It should be disinfected two or three times a week. It is recommended that the toothbrush head should be replaced every three months. It can be disinfected every day. The SEGA toothbrush sterilizer I selected should be disinfected for 6-8 minutes each time. It is a good ultraviolet disinfection lamp. It needs to be equipped with a ballast. Mould formation is due to long-term lack of ventilation and humidity, Ultraviolet sterilization equipment programme If ventilation and moisture removal are available, mold will not grow. Since mold has been formed, first kill it with a mold remover, and then put a moisture bag such as a charcoal bag. I often do on-site mildew and odor removal projects. You can sprinkle lime on the corner of the wall or place charcoal in the house to absorb moisture when the house is wet. In addition, don't open the window in foggy or rainy weather. Open the window in good weather to ventilate in time.

Share to