When installing microwave and ultraviolet water treatment equipment, the command must be strengthened to prevent equipment collision. Customized Microwave cleaning equipment And these important devices are assigned special management, storage and storage problems. Microwave cleaning equipment manufactor In the field of construction, prepare sufficient quantity and quality of fire-fighting tools for inspection, and require them to use only in case of fire. The construction personnel entering the site shall be checked and wear qualified protective equipment, such as safety helmet, because personal safety is very important.

After years of development, microwave electrodeless UV sterilization equipment has been widely used in drinking water, food, beverages, electronic products, chemicals, medicine, sewage microwave UV water treatment equipment and other fields. Microwave cleaning equipment manufactor High intensity odorless UV germicidal lamp is used to simplify the special stainless steel inner wall, so that the pretreated water has enough UV when passing through the UV. Customized Microwave cleaning equipment Irradiation has good sterilization effect. In addition, it has the advantages of simplicity, convenience, broad-spectrum, no secondary pollution, convenient management and automation.

With the extension of the use time of the clean microwave ultraviolet water treatment equipment, it is a normal phenomenon that the water production decreases. The decrease of water production in winter is due to the decrease of water temperature and permeability, and the change of reverse osmosis membrane density. These two reasons will reduce the water production of microwave and ultraviolet water treatment equipment. Strengthen pretreatment device, Customized Microwave cleaning equipment Increasing the cleaning time, replacing the filter element frequently, backwashing the reverse osmosis membrane in time, and extending the interval are all ways to promote the normal operation of the microwave ultraviolet water treatment equipment. Microwave cleaning equipment manufactor If the water pipe or microwave ultraviolet water treatment equipment is frozen, the valve shall be closed in time, wrapped with towel, and slowly watered with warm water. Do not directly use fire for barbecue, nor use boiling water for heating, so as to prevent microwave and ultraviolet water treatment equipment and pipelines from cracking, or use a hair dryer to dry them. At the same time, gently tap hard objects on the water pipe until the pipe freezes and thaws, and the tap water flows out smoothly. If the fully automatic frequency conversion water supply equipment has been frozen, it can only be wrapped with a hot towel and sprinkled with warm water until the pipe freezes and thaws, so that the water can flow out smoothly.

Microwave electrodeless ultraviolet sterilization equipment has high value in microwave ultraviolet water treatment equipment, Customized Microwave cleaning equipment It destroys and changes the structure of DNA of microorganisms through the irradiation of ultraviolet light, so that the bacteria will die immediately or cannot reproduce, so as to achieve the purpose of sterilization. The real bactericidal effect is UVC ultraviolet, Microwave cleaning equipment manufactor Because C-band ultraviolet light is easily absorbed by the DNA of organisms, the ultraviolet light of about 253.7 nm is preferred. It is a pure physical disinfection method, which has the advantages of simplicity, convenience, broad-spectrum, no secondary pollution, convenient management and automation. With the introduction of various new designed ultraviolet lamps, the application range of ultraviolet sterilization is also expanding.

Compared with ordinary vacuum cleaners, the industrial central dust collector has a powerful dust collection function and can be cleaned quickly, avoiding secondary pollution caused by dust and noise pollution: 1. The dusty gas enters the ash hopper of each sub room from the air inlet equalizing pipe of the dust remover. The central dust removal of the workshop is customized and guided by the ash hopper guide device. 　　 2. The large particles of dust are separated and directly fall into the ash hopper, while the fine dust enters the middle box evenly and is adsorbed on the outer surface of the filter bag. Clean gas enters the upper box through the filter bag and is discharged into the atmosphere through offline valves and exhaust pipes. 　　 3. Timing or manual cleaning can be adopted: each chamber of the pulse bag filter will be cleaned in turn, and the chamber that has completed the cleaning will be restored to the dedusting state immediately. 　　 4. Open the electric control pulse valve according to the set procedure, stop air blowing, use the compressed air instantaneous blowing to increase the pressure in the filter bag, shake the dust on the filter bag into the ash bucket, and discharge it by the ash discharge mechanism. 　　 5. With the increasing dust on the outer surface of the filter bag, the differential pressure monitoring system will send a signal when the equipment resistance reaches the set value. 　　 6. The dust removal mechanism starts to work, and compressed air is sprayed from the pulse valve, and then shot into the filter bag through the blowing pipe and nozzle. The filter bag expands and vibrates instantaneously, so that the dust on the surface is removed and dropped into the ash hopper, which is discharged by the ash discharge valve. 　　 7. With the progress of filtering conditions, the dust on the filter bag will accumulate more and more. When the equipment resistance reaches the limited resistance value, the ash removal control device will automatically close the offline valve of one chamber according to the differential pressure setting value or the ash removal time setting value.