Maintaining chlorine or bromine levels in public swimming pools, or even in private swimming pools at home, is an important first stage in preventing bacteria that cause recreational diseases. The weekly test will greatly help you with the proper care you need to keep the pool water clean and safe for everyone to enjoy. Taking time to monitor the level of chemicals in the pool will prevent you from needing to monitor your health later. Microwave drying equipment programme Installing microwave electrodeless ultraviolet sterilization equipment can eliminate pathogens and bacteria, which will reduce the effectiveness of chlorine and will not leave any residue. production Microwave drying equipment Ultraviolet is safe and is a widely used sterilization method for water, air and medical supplies. Most people who get sick because of recreational water will have diarrhea, cough, eye pain and even skin rashes. When people enter the pool without taking a shower, they are introducing bacteria, such as sweat, feces and any other bacteria they come in contact with.

Intelligent sprinkler system Intelligent high-pressure fog pile system Fusen deodorization of waste transfer station

Application industry: It is applicable to odor control in municipal sewage, sewage pump station, garbage treatment plant (station), petroleum and petrochemical industry, pharmaceutical and chemical industry, food processing, spraying, printing prevention, leather processing and other production industries.

According to the source of sewage, sewage microwave ultraviolet water treatment equipment mainly includes production sewage microwave ultraviolet water treatment equipment and domestic sewage microwave ultraviolet water treatment equipment. The former refers to industrial sewage microwave ultraviolet water treatment equipment and hospital sewage microwave ultraviolet water treatment equipment, while domestic sewage mainly refers to sewage generated in daily life, municipal sewage microwave ultraviolet water treatment equipment, etc. Sewage quality includes TSS, namely suspended solids in water, sewage type and proportion, etc. The types of sewage and water quality are different. When choosing ultraviolet sterilization equipment, production Microwave drying equipment It shall be configured differently. Water volume mainly refers to the average flow and peak flow of sewage to be treated. Secondly, consider whether the equipment operation time is 24 hours or intermittent water supply. In addition, Microwave drying equipment programme In addition, the discharge standards for effluent quality requirements and the bacterial indicators and requirements for sewage inflow and outflow shall be considered, and the number of modules required for the UV sterilization equipment of the sewage microwave UV water treatment equipment, the number of lamps included in the module, and the discharge distance of the module shall be specifically designed. In addition, when selecting equipment, we must first determine the treatment water quantity, water quality, discharge standards and other factors. In the process of model selection, the quality, service life and after-sales service of ultraviolet sterilization equipment should be comprehensively investigated.

The power supply is the foundation and should be used carefully. Generally, it needs to work under 200V/50Hz AC power, production Microwave drying equipment In order to ensure the correct operation of the complete set of automatic water softening device. Microwave drying equipment programme The manufacturer of the microwave and ultraviolet water treatment equipment shall ensure that the power cannot be cut off, and that the switch of the equipment cannot be cut to the point, so as to prevent the quality problems of the softening microwave and ultraviolet water treatment equipment and the increase of equipment loss.

RCO organic waste gas catalytic combustion purification equipment can effectively purify the environment, pollution, improve labor operating conditions, ensure the health of workers, and the heat emitted can be recycled to reduce production costs. RCO organic waste gas catalytic combustion equipment has perfect system design, complete auxiliary equipment, high purification efficiency and high automation. RCO organic waste gas catalytic combustion equipment RCO organic waste gas catalytic combustion purification device is designed based on two basic principles of adsorption and catalytic combustion, namely adsorption concentration catalytic combustion method. The dedusting equipment adopts the working mode of single bed adsorption purification of organic waste gas and catalytic combustion device regeneration and activation of activated carbon. Firstly, the organic waste gas with low concentration is adsorbed by activated carbon, and the adsorption operation is stopped when it is almost saturated, then the organic matter is desorbed from the activated carbon by hot gas flow to regenerate the activated carbon; The desorbed organic matter has been concentrated (the concentration is dozens of times higher than the original) and sent to the catalytic combustion chamber for catalytic conversion into CO2 and H2O for emission; When the concentration of organic waste gas reaches above 2000ppm, the organic waste gas can maintain spontaneous combustion in the catalytic bed without external heating. Some of the burned tail gas is discharged into the atmosphere, and most of it is sent to the adsorption bed for desorption and regeneration of activated carbon. In this way, the heat energy required for combustion and desorption can be met to save energy. The regenerated activated carbon can be used for the next adsorption.? RCO organic waste gas catalytic combustion equipment uses catalytic combustion method to convert toxic and harmful organic gas into non-toxic gas.? The main structure of RCO organic waste gas catalytic combustion equipment is composed of three major parts: purification device host, induced draft fan and control system. The catalytic combustion purification device includes: dedusting flame arrester, heat exchanger, preheater and catalytic combustion chamber. The organic waste gas enters the preprocessor from the air inlet at the upper part of the equipment, passes through the coarse filter element composed of multi-layer stainless steel wire mesh to remove dust and other particles in the waste gas, and enters the combined adsorption bed from the main channel at the lower part of the device (two rows in parallel with six grids). Each adsorption bed is equipped with a set of pneumatic switch valve, which can change the adsorption bed into adsorption/desorption state. The longitudinal section of the adsorption bed from bottom to top is respectively the inlet manifold, adsorption chamber, air purification chamber and outlet manifold. The adsorption chamber and the air purification chamber are separated by a flower plate, under which a number of adsorption cylinders are hoisted. The waste gas entering the adsorption chamber passes through the adsorption layer through the outer wall of the adsorption cylinder, VOCs are adsorbed by a large number of microporous surfaces of the adsorbent, and the waste gas is purified and then enters the air purification chamber upward through the flower plate holes, Then it enters the main outlet pipe through the switching valve and is discharged by the fan. One of the six adsorption chambers must be in the desorption state, and the other five must be in the adsorption state. Generally, the desorption time is 12 minutes, that is, the adsorption bed responsible for the adsorption work can be desorbed and regenerated once every hour. This work process of the device coincides with the name of the invention zhuanli - a kind of compartment offline desorption bag type adsorption equipment. Its process principle is the same as that of the pulse reverse blow compartment offline bag type dust collector, except that the purification process of the device is "physical adsorption", The bag filter purification process is "physical filtration". The desorption working medium of the adsorption bed is hot air, which is provided by the catalytic combustion device. Generally, the temperature of the hot air is ≤ 150 ℃, which is determined by the boiling point of different VOCs and the saturated vapor partial pressure at the desorption temperature.