With the extension of the use time of the clean microwave ultraviolet water treatment equipment, it is a normal phenomenon that the water production decreases. The decrease of water production in winter is due to the decrease of water temperature and permeability, and the change of reverse osmosis membrane density. These two reasons will reduce the water production of microwave and ultraviolet water treatment equipment. Strengthen pretreatment device, Customized Microwave drying of cereals Increasing the cleaning time, replacing the filter element frequently, backwashing the reverse osmosis membrane in time, and extending the interval are all ways to promote the normal operation of the microwave ultraviolet water treatment equipment. Microwave drying of cereals manufactor If the water pipe or microwave ultraviolet water treatment equipment is frozen, the valve shall be closed in time, wrapped with towel, and slowly watered with warm water. Do not directly use fire for barbecue, nor use boiling water for heating, so as to prevent the microwave and ultraviolet water treatment equipment and pipes from cracking, or use a hair dryer to dry them. At the same time, gently tap hard objects on the water pipe until the pipe freezes and thaws, and the tap water flows out smoothly. If the fully automatic frequency conversion water supply equipment has been frozen, it can only be wrapped with a hot towel and sprinkled with warm water until the pipe freezes and thaws, so that the water can flow out smoothly.

Application industry: It is applicable to the disinfection and preservation of air, water, objects, fruits and vegetables, grains and other viruses and bacteria, grain storage, feed bait, marine lakes and other bacterial carriers in indoor and outdoor spaces of all walks of life.

Application industry: Application scope of electric rapping: it is suitable for casting, metal processing, refractory, ceramics, glass, cement, mineral aggregate, plastic, chemical and other industries and other places with dust pollution.

The catalytic combustion equipment for waste gas treatment is mainly used as a supporting part of the catalytic bed electric heating oxidation combustion system in the CO/RCO adsorption+desorption+catalytic combustion system. It is widely applicable to the purification and odor elimination of hazardous waste gas volatilized or leaked from painting, printing, household appliances, footwear, plastics and various chemical workshops, and is suitable for low concentration (1501000) The organic waste gas that is not suitable for direct combustion or catalytic combustion and recovery treatment will be concentrated by activated carbon adsorption, and then the high concentration organic waste gas will be removed through the desorption procedure and sent to the unit for thermal oxidation reaction. The self heating effect of the organic waste gas catalytic reaction can greatly reduce the heat consumption of the electric heater, especially for the treatment sites with large air volume, Satisfactory economic and social benefits can be obtained. Application scope of exhaust gas catalytic combustion equipment: 1. Industrial applications: common pollutants discharged from petrochemical, light industry, plastics, printing, coating and other industries; 2. Waste gas type application: hydrocarbon compounds (aromatics, alkanes, olefins), benzene, ketones, phenols, alcohols, ethers, alkanes and other compounds; Features of catalytic combustion equipment for waste gas treatment: 1. Convenient operation: fully automatic control during operation. 2. Low energy consumption: during normal operation, the equipment operates at low power (or no power) because the exhaust gas has some concentration. 3. Stable performance: pressure relief and self protection, fire resistance and dust removal, over temperature alarm and automatic control. 4. Low resistance: honeycomb ceramic catalyst impregnated with today's advanced precious metal palladium and platinum has a large specific surface area. 5. Small floor area: only 70% of the same products in the same industry. 6. Long service life: the catalyst is usually replaced within 4 years

The sterilization principle of microwave electrodeless ultraviolet sterilization equipment is to use the sterilization ability of ultraviolet light. Can ultraviolet light directly kill microorganisms? Microwave drying of cereals manufactor According to different biological effects, ultraviolet light is generally divided into four parts according to wavelength: A-band (UV-A), Customized Microwave drying of cereals Also known as black spot effect ultraviolet (400 ～ 320 nm); B band (UV-B), also known as erythema effect ultraviolet (320 ～ 275 nm); C-band (UV-C), also known as sterilization ultraviolet (275 ～ 200 nm); D-band (UV-D), also known as vacuum ultraviolet ray (200-100 nm). C-band ultraviolet light is mainly used for water disinfection.

UV disinfection is generally only used for air and instrument surface disinfection. Surgical dressings cannot be treated by UV radiation as a routine method. Ultraviolet radiation is the general term of radiation in electromagnetic spectrum with wavelength from 10nm to 400nm, which can not cause people's vision. In 1801, German physicist Ritter found that the ultraviolet ray could sensitize the photographic negative containing silver bromide at the outer part of the ultraviolet end of the sunlight spectrum, so he found the existence of ultraviolet ray. Too much ultraviolet rays entering the body will cause skin cancer. Customized Microwave drying of cereals It can be disinfected after use every day. It should be disinfected two or three times a week. It is recommended that the toothbrush head should be replaced every three months. It can be disinfected every day. The SEGA toothbrush sterilizer I selected should be disinfected for 6-8 minutes each time. It is a good ultraviolet disinfection lamp. It needs to be equipped with a ballast. Mould formation is due to long-term lack of ventilation and humidity, Microwave drying of cereals manufactor If ventilation and moisture removal are available, mold will not grow. Since mold has been formed, first kill it with a mold remover, and then put a moisture bag such as a charcoal bag. I often do on-site mildew and odor removal projects. You can sprinkle lime on the corner of the wall or place charcoal in the house to absorb moisture when the house is wet. In addition, don't open the window in foggy or rainy weather. Open the window in good weather to ventilate in time.